R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
 
Page 1 of 14
1
2
3
11
Last »
Search: Posts Made By: lowey79
Showing results 1 to 25 of 344
Search took 0.03 seconds.
Forum: Nitro Off-Road
06-16-2010, 06:34 AM
Replies: 12,372
Views: 1,283,926
Posted By lowey79

One thing you can try to get it to turn is try 2F...

One thing you can try to get it to turn is try 2F 7C 5R diff oils... i know it sounds backward, but it gives the 808 lightning fast off power steering and a little push on thottle! Also, try lift the...
Forum: Offroad Nitro Engine Forum
05-27-2010, 05:28 AM
Replies: 2,883
Views: 454,746
Posted By lowey79

The midrange is a usfull adjustment if you know...

The midrange is a usfull adjustment if you know what you're doing... It adjusts the fuel mixture in the transition from LSN to HSN by the position of the fuel delivery jet in relation to the throttle...
Forum: Offroad Nitro Engine Forum
05-26-2010, 07:44 PM
Replies: 2,883
Views: 454,746
Posted By lowey79

For those that are playing with the mid adjuster,...

For those that are playing with the mid adjuster, it doesn't matter where the hole is because the is a channel in the assembly that insures that there is always fuel getting to the jet... The factory...
Forum: Nitro Off-Road
05-23-2010, 06:24 AM
Replies: 4
Views: 1,691
Posted By lowey79

Best clutch in the business IMO! If you got the...

Best clutch in the business IMO! If you got the newer version that has the oring in the adjusting nut, then you almost don't need to loctite it! I've found the best setup in my 808 is carbon shoes,...
Forum: Offroad Nitro Engine Forum
05-20-2010, 06:48 AM
Replies: 2,883
Views: 454,746
Posted By lowey79

There are many different methods of breaking in a...

There are many different methods of breaking in a motor and they all have good points and bad... Personally i prefer the heat cycle method where by i keep it rich and maintain minimum 100°C with the...
Forum: Nitro Off-Road
05-11-2010, 07:01 AM
Replies: 12,372
Views: 1,283,926
Posted By lowey79

Another thing you want to do to get clearance is...

Another thing you want to do to get clearance is loosen the set screws in the blue circles and move the brake levers in the direction of the red arrows... This should give you i slight front brake...
Forum: Offroad Nitro Engine Forum
05-06-2010, 07:44 PM
Replies: 2,883
Views: 454,746
Posted By lowey79

I'd probably start on 0.5 turn in from flush on...

I'd probably start on 0.5 turn in from flush on the LSN and 2.5 turns out on the HSN.
Forum: Offroad Nitro Engine Forum
05-06-2010, 07:17 AM
Replies: 2,883
Views: 454,746
Posted By lowey79

Fair enough... I love the power delivery from my...

Fair enough... I love the power delivery from my Speed.. I find it very smooth for the way "I" drive... I've found Nova's to be flat in comparison. Everyone's different i guess! Yet to try an RB...
Forum: Offroad Nitro Engine Forum
05-06-2010, 06:40 AM
Replies: 2,883
Views: 454,746
Posted By lowey79

The Speed is one of the most linear (smooth)...

The Speed is one of the most linear (smooth) motors i've ever seen in it's power delivery so i would say that there is exceptions to this statement?
Forum: Onroad Nitro Engine Zone
05-04-2010, 07:58 PM
Replies: 316
Important: "the tuning bible"
Views: 343,945
Posted By lowey79

Could be an air leak then? Is it a GRP...

Could be an air leak then?

Is it a GRP ninja or a OS ninja? If it's OS with a 3 needle carb You could try adjusting the mid needle... I'd try half a turn in to start with and no more than 1 turn!...
Forum: Offroad Nitro Engine Forum
05-04-2010, 07:58 PM
Replies: 517
Views: 288,992
Posted By lowey79

Could be an air leak then? Is it a GRP...

Could be an air leak then?

Is it a GRP ninja or a OS ninja? If it's OS with a 3 needle carb You could try adjusting the mid needle... I'd try half a turn in to start with and no more than 1 turn!...
Forum: Onroad Nitro Engine Zone
05-03-2010, 07:35 PM
Replies: 316
Important: "the tuning bible"
Views: 343,945
Posted By lowey79

That sounds like it's rich on the LSN... Try...

That sounds like it's rich on the LSN... Try leaning it a little and run it around your yard again... it should now idle up for a bit longer. If it does you're on the right track... keep leaning till...
Forum: Offroad Nitro Engine Forum
05-03-2010, 07:35 PM
Replies: 517
Views: 288,992
Posted By lowey79

That sounds like it's rich on the LSN... Try...

That sounds like it's rich on the LSN... Try leaning it a little and run it around your yard again... it should now idle up for a bit longer. If it does you're on the right track... keep leaning till...
Forum: Onroad Nitro Engine Zone
05-03-2010, 07:06 AM
Replies: 316
Important: "the tuning bible"
Views: 343,945
Posted By lowey79

It can mean that you're running slightly rich on...

It can mean that you're running slightly rich on the LSN and the idle gap is too wide... If it's a lean idle, generally it will idle high and the exhaust note will sound fluffy.

Best way to check...
Forum: Offroad Nitro Engine Forum
05-03-2010, 07:06 AM
Replies: 517
Views: 288,992
Posted By lowey79

It can mean that you're running slightly rich on...

It can mean that you're running slightly rich on the LSN and the idle gap is too wide... If it's a lean idle, generally it will idle high and the exhaust note will sound fluffy.

Best way to check...
Forum: Painting, Designs, Graphics and Photography
04-28-2010, 07:35 AM
Replies: 2
Views: 735
Posted By lowey79

Paint or Airbrush problem?

I'm using pactra enamels and i'm finding it difficult to do fine shadowing with pearl colours! They seem to only want to flow when i open the needle further which applies too much paint for what i'm...
Forum: Nitro Off-Road
09-23-2009, 04:23 AM
Replies: 12,372
Views: 1,283,926
Posted By lowey79

That's a fair piont, but how many of those other...

That's a fair piont, but how many of those other bugbies are in the field compared to xray?... Losi always seem to do well, but there are four times as many of them at any given event!
Forum: Nitro Off-Road
09-21-2009, 07:28 PM
Replies: 12,372
Views: 1,283,926
Posted By lowey79

Try going to 5-7k in the rear! I know it sounds...

Try going to 5-7k in the rear! I know it sounds wierd, but it really gives you a lot of turn in! It worked for me, before i got the active diff!
Forum: Offroad Nitro Engine Forum
09-21-2009, 04:38 AM
Replies: 2,883
Views: 454,746
Posted By lowey79

The mid adjustment is not as sensitive as the...

The mid adjustment is not as sensitive as the other adjustments on your carb but what a lot of people don't realise is that moving the mid also changes the LSN setting. so if you adjust the Mid you...
Forum: Onroad Nitro Engine Zone
09-21-2009, 04:20 AM
Replies: 316
Important: "the tuning bible"
Views: 343,945
Posted By lowey79

Sounds like you may have an air leak somewhere?...

Sounds like you may have an air leak somewhere? Pull the back plate and carb out. Check the rear inside of the case for cracks (where the back plate slides in) This was a problem on some earlier...
Forum: Offroad Nitro Engine Forum
09-21-2009, 04:20 AM
Replies: 517
Views: 288,992
Posted By lowey79

Sounds like you may have an air leak somewhere?...

Sounds like you may have an air leak somewhere? Pull the back plate and carb out. Check the rear inside of the case for cracks (where the back plate slides in) This was a problem on some earlier...
Forum: Nitro Off-Road
09-20-2009, 02:26 AM
Replies: 12,372
Views: 1,283,926
Posted By lowey79

Well it finally happened today... After over a...

Well it finally happened today... After over a year of racing and some big spills, i finally broke my first part on my 808.... A front upper link end...

I'm super impressed with the durability of...
Forum: Nitro Off-Road
08-17-2009, 05:39 AM
Replies: 12,372
Views: 1,283,926
Posted By lowey79

OS Speed AL, OS 2060WN pipe set

OS Speed AL, OS 2060WN pipe set
Forum: Offroad Nitro Engine Forum
08-16-2009, 07:29 PM
Replies: 2,883
Views: 454,746
Posted By lowey79

Just leave it alone... There aren't really any...

Just leave it alone... There aren't really any gains to be made by adjusting the mid....
Forum: Offroad Nitro Engine Forum
08-09-2009, 03:50 AM
Replies: 2,883
Views: 454,746
Posted By lowey79

You should be right leave that rod in it then......

You should be right leave that rod in it then... I would change it when the front bearing goes!
Showing results 1 to 25 of 344
 
Page 1 of 14
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.