R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
Search: Posts Made By: MötleyRöx
Showing results 1 to 16 of 16
Search took 0.01 seconds.
01-29-2010, 04:33 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Uh... ok. But, I really don't mean to argue,...

Uh... ok.

But, I really don't mean to argue, anyway. All input is good input.
Thanks. ;):tire:
01-29-2010, 04:06 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

What does the 8x1 mean? ... other than 8 ...

What does the 8x1 mean?
... other than 8 :deathstar
01-29-2010, 10:16 AM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Limit of turns on these old MSCs? I'm thinking...

Limit of turns on these old MSCs?
I'm thinking I'd like something a bit below 20 turns.
Possibly even down to a 13 turn.

I'm sure its all narrowed down to how much amperage the resistor is...
01-28-2010, 03:48 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

I got to actually run it yesterday. Installed...

I got to actually run it yesterday.
Installed two hardwired fans, one over the motor and one toward the MSC.
Ran great at full throttle and the occasional half throttle.
Never was too hot to...
01-24-2010, 10:18 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Ebay auction... watching. ;)

Ebay auction... watching. ;)
01-24-2010, 09:03 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Oh yes... almost forgot. FULL THROTTLE IT...

Oh yes... almost forgot.

FULL THROTTLE IT IS!

:tire::flaming::tire:
01-24-2010, 09:02 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

OK then... it seems to me that this is somewhat...

OK then... it seems to me that this is somewhat of an intentional wear type of part.

I'll do my best not to overheat it. But, directing energy involves heat.
Thanks everyone!
01-24-2010, 06:57 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Could you explain the difference? Its been a...

Could you explain the difference?
Its been a long time since I ran a brushed system and I was about 12 years old and could have cared less about lay down or stand up brushes back then. ;)
01-24-2010, 06:47 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Not sure if its three step... there are 8...

Not sure if its three step... there are 8 connection points between neutral and WOT.
The one that was used previously had uneven spacing between a few of the lines... this one is a constant...
01-24-2010, 06:31 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Thanks for understanding... I sometimes get the...

Thanks for understanding... I sometimes get the same type of remarks asking why I ride an old Honda 350four. :cool: But, they all come from Harley riders, go figure.
01-24-2010, 06:29 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Never full throttle while I was testing it. I...

Never full throttle while I was testing it.
I have not been able to really run it yet.

I wasn't even really half throttle.

Only ran for about a minute or 2... total run time was probably less...
01-24-2010, 06:24 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Its an old Green Machine 2. I also have a stock...

Its an old Green Machine 2.
I also have a stock Reedy Mr Outlaw... still need to solder the connection on.

Both are 27 turn.
01-24-2010, 06:19 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

I don't believe the 10T came w/ such a resistor...

I don't believe the 10T came w/ such a resistor surrounded by a metal cage.
The resistor is directly above the servo... I do have concerns that I could melt the servo. Especially, since its barely...
01-24-2010, 06:15 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

It was actually about a minute of runtime at very...

It was actually about a minute of runtime at very slow speed... I was testing inside my office lobby at work.

This, I would think, would be when the resistor would be hottest, because it is doing...
01-24-2010, 06:13 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Yep, I have brushless system. I'm experimenting....

Yep, I have brushless system. I'm experimenting.

But I'm a very vintage oriented guy... old houses, old motorcycles, old cars, old RC stuff

Don't be so concerned about what you think I...
01-24-2010, 05:58 PM
Replies: 31
Views: 12,720
Posted By MötleyRöx

Mechanical speed control resistor getting VERY HOT

Hi all...

I just set up my wiper type speed control on my old RC10T.
All new wiring, checked, double checked and triple checked... its good.
The resistor is brand new... there was a different...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.