45LikesHobbywing xr10 pro
03-06-2018, 09:59 AM
#376
Tech Master
iTrader: (5)
Yep - do this. I had a similar problem and it turned out the sensor cable wasn't plugged into the esc all the way. The cable was slightly short and the chassis flex started to pull it out, this was on a 17.5 buggy. Replaced with a longer cable and the problem went away.
03-09-2018, 04:13 PM
#378
So got to run the car with jumps over the last few days and so far, so good. I think it came down to a loose ESC-to-rx connection. If it becomes a problem again, I'll switch it from a Spektrum plug (stock) to a Futaba plug.
05-13-2018, 02:47 PM
#379
Anyone having issues with the new usb link please email me at [email protected] .
I will be able to send you a copy of the firmware.
please note: No gmail.com email address as they dont except exe files.
I will be able to send you a copy of the firmware.
please note: No gmail.com email address as they dont except exe files.
05-19-2018, 06:43 PM
#380
I have a XR10 stock spec and using it in VTA with a R1 V16 25.5 motor. The rsc worked fine in my 17.5 TC. After about 2 to 3 minutes it loses power. The light on the esc starts flashing green instead of red. If I turn it off and back on it will flash red and run fine for a couple of minutes. Checked data on esc and it shows 34000rpms, if it is running right it shows about 17000 rpms. Tried turning off low voltage and thermal sensors in esc and it did not help. Tried running it on bench for about 6 or 7 minutes and it did not do it.
Any suggestions?
Any suggestions?
05-19-2018, 07:00 PM
#381
Change sensor cable , reload software from usb link and re-calibrate radio to esc and all will go back to normal.
05-22-2018, 05:16 PM
#384
How is the esc compare to Sanwa Super Vortex Gen 2 Pro?
05-28-2018, 09:32 PM
#386
05-29-2018, 11:52 AM
#387
As much of a Sanwa fan as I am, in my mind they just aren't an ESC company. Great radios, good servos - that's all they are for me. My first Hobbywing XR-10s however, have convinced me so much, that I started to put them into my whole off-road fleet.
05-31-2018, 09:03 PM
#388
Tech Adept
Just in case I missed it, anyone using this ESC with the V10 G3?
Care to share your experience?
Care to share your experience?
06-02-2018, 06:02 PM
#389
Tech Apprentice
Quick question? Not sure if this has been asked but will ask again.
Today on my xr10 pro when turning it on, I used mt 2mm mip driver and as I pressed the button down, I accidentally shorted the driver across the fan/setup prongs. There was some sparks. Speed control continued to work but when I pressed the button the motor turned off but the speedo fan and servo kept running. Had to turn it off by unplugging battery.
I was able to go through the setup process and use speed control properly, it just won’t shut off with the button.
anything I can do to fix or reset it it? Or just be thankful it works 98%. Lol
Today on my xr10 pro when turning it on, I used mt 2mm mip driver and as I pressed the button down, I accidentally shorted the driver across the fan/setup prongs. There was some sparks. Speed control continued to work but when I pressed the button the motor turned off but the speedo fan and servo kept running. Had to turn it off by unplugging battery.
I was able to go through the setup process and use speed control properly, it just won’t shut off with the button.
anything I can do to fix or reset it it? Or just be thankful it works 98%. Lol
06-03-2018, 06:46 PM
#390
Tech Adept