Revo Roller Big Block - Steel RRP tranny OS 30VG
#1
Revo Roller Big Block - Steel RRP tranny OS 30VG
Revo roller complete $300
or in parts
**************
- will sell the all steel tranny with extra gears for $90
- os30 vg motor and pipe for $50
- roller with big block mount/rpms/technoupgrades/ steel cvd for $170
shipping included
__________
- RC-Monster 1/8 scale diffs front and rear with big beefy HPI 1/8 scale diffs installed
-complete RRP steel tranny (close ratio gears) with rear brakes
-extra set of RRP close ratio and standard ratio gears new in package
-Qoncepts Big Block Motor mount
-Unmounted OS 30 vg motor (repaired ) with tuned pipe
-RPM/Techno arms
-250 cc gas tank
-Extra 300cc gas tank
-techno receiver and battery box
-Rpm knuckles
-Boca bearings
-steel cvd all 4 corners and center
-Aluminum shocks
-aluminum single steering arm
-red aluminum pushrods/links
Trucks needs some tlc and a few odds and ends to be complete (wheel hubs, front shock tower, servo,screws )
-OS 30 vg motor was repaired . Motor was hit from the bottom and had a 2mm dent/crack in the outer casing. Did not penetrate the block, but site was covered with JB Weld and gave no problems.
looking for $300 shipped - may part out for the right prices
damage to motor :
As you can see the motor took some light hits (2mm hits) one hit also made a 2mm crack on the bottom. The crack was not open and did not penetrate the block itself (no air escaped under compression) but I laid a coat of JB weld across the bottom of the motor to securely seal it just in case, and it never gave any problems.
Also I forgot to mention this truck has RC Monster 1/8th sized aluminum diffs. - A $150 value in itself
This is a sample pictures of the aluminum diffs - they are installed And I am not pulling them out - again this is only a SAMPLE picture of the installed aluminum diffs
Qoncepts Big Block motor mount
Robinson Racing steel gears in the tranny
RC-Monster hybrid diffs with big beefy HPI 1/8 scale diffs installed
Tekno wing and rx/battery box conversion.
Tekno extended rear a-arms, RPM carriers and front a-arms.
Ofna #19504 Fuel Tank 1/7th Scale) 250cc Ofna tank for extended run time
Prices (NEW)
RC-Monster 1/8 scale diffs front and rear = $150
OS 30VG engine with non-pull start back plate = $220
Tekno wing = $25
Tekno Servo tray, rx/battery box = $30
Ofna 250cc fuel tank = $16
Integy Alloy steering saver = $26
Integy alloy shock ball ends = $7
Robinson steel gears = $100
Boca ceramic main bearings = $75
1/8 scale CEN tuned pipe = $60
or in parts
**************
- will sell the all steel tranny with extra gears for $90
- os30 vg motor and pipe for $50
- roller with big block mount/rpms/technoupgrades/ steel cvd for $170
shipping included
__________
- RC-Monster 1/8 scale diffs front and rear with big beefy HPI 1/8 scale diffs installed
-complete RRP steel tranny (close ratio gears) with rear brakes
-extra set of RRP close ratio and standard ratio gears new in package
-Qoncepts Big Block Motor mount
-Unmounted OS 30 vg motor (repaired ) with tuned pipe
-RPM/Techno arms
-250 cc gas tank
-Extra 300cc gas tank
-techno receiver and battery box
-Rpm knuckles
-Boca bearings
-steel cvd all 4 corners and center
-Aluminum shocks
-aluminum single steering arm
-red aluminum pushrods/links
Trucks needs some tlc and a few odds and ends to be complete (wheel hubs, front shock tower, servo,screws )
-OS 30 vg motor was repaired . Motor was hit from the bottom and had a 2mm dent/crack in the outer casing. Did not penetrate the block, but site was covered with JB Weld and gave no problems.
looking for $300 shipped - may part out for the right prices
damage to motor :
As you can see the motor took some light hits (2mm hits) one hit also made a 2mm crack on the bottom. The crack was not open and did not penetrate the block itself (no air escaped under compression) but I laid a coat of JB weld across the bottom of the motor to securely seal it just in case, and it never gave any problems.
Also I forgot to mention this truck has RC Monster 1/8th sized aluminum diffs. - A $150 value in itself
This is a sample pictures of the aluminum diffs - they are installed And I am not pulling them out - again this is only a SAMPLE picture of the installed aluminum diffs
Qoncepts Big Block motor mount
Robinson Racing steel gears in the tranny
RC-Monster hybrid diffs with big beefy HPI 1/8 scale diffs installed
Tekno wing and rx/battery box conversion.
Tekno extended rear a-arms, RPM carriers and front a-arms.
Ofna #19504 Fuel Tank 1/7th Scale) 250cc Ofna tank for extended run time
Prices (NEW)
RC-Monster 1/8 scale diffs front and rear = $150
OS 30VG engine with non-pull start back plate = $220
Tekno wing = $25
Tekno Servo tray, rx/battery box = $30
Ofna 250cc fuel tank = $16
Integy Alloy steering saver = $26
Integy alloy shock ball ends = $7
Robinson steel gears = $100
Boca ceramic main bearings = $75
1/8 scale CEN tuned pipe = $60
Last edited by noir522; 05-25-2011 at 05:10 PM.
#2
I also have a shell and a set of 17mm or 24mm adapters I could add in.
#3
bumpin 4 the day
#4
price is negotiable
#5
todays allotted bumpage with new prices
#6
still available
#8
damage to motor :
As you can see the motor took some light hits (2mm hits) on hit also made a 2mm scrock on the bottom. The crack was not open and did not penetrate the block itself (no air escaped under compression) but I laid a coat of JB weld across the bottom of the motor to securely seal it just in case, and it never gave any problems.
Also I forgot to mention this truck has RC Monster 1/8th sized aluminum diffs. - A $150 value in itself
Qoncepts Big Block motor mount
Robinson Racing steel gears in the tranny
RC-Monster hybrid diffs with big beefy HPI 1/8 scale diffs installed
Tekno wing and rx/battery box conversion.
Tekno extended rear a-arms, RPM carriers and front a-arms.
Ofna #19504 Fuel Tank 1/7th Scale) 250cc Ofna tank for extended run time
Prices (NEW)
RC-Monster 1/8 scale diffs front and rear = $150
OS 30VG engine with non-pull start back plate = $220
Tekno wing = $25
Tekno Servo tray, rx/battery box = $30
Ofna 250cc fuel tank = $16
Integy Alloy steering saver = $26
Integy alloy shock ball ends = $7
Robinson steel gears = $100
Boca ceramic main bearings = $75
1/8 scale CEN tuned pipe = $60
As you can see the motor took some light hits (2mm hits) on hit also made a 2mm scrock on the bottom. The crack was not open and did not penetrate the block itself (no air escaped under compression) but I laid a coat of JB weld across the bottom of the motor to securely seal it just in case, and it never gave any problems.
Also I forgot to mention this truck has RC Monster 1/8th sized aluminum diffs. - A $150 value in itself
Qoncepts Big Block motor mount
Robinson Racing steel gears in the tranny
RC-Monster hybrid diffs with big beefy HPI 1/8 scale diffs installed
Tekno wing and rx/battery box conversion.
Tekno extended rear a-arms, RPM carriers and front a-arms.
Ofna #19504 Fuel Tank 1/7th Scale) 250cc Ofna tank for extended run time
Prices (NEW)
RC-Monster 1/8 scale diffs front and rear = $150
OS 30VG engine with non-pull start back plate = $220
Tekno wing = $25
Tekno Servo tray, rx/battery box = $30
Ofna 250cc fuel tank = $16
Integy Alloy steering saver = $26
Integy alloy shock ball ends = $7
Robinson steel gears = $100
Boca ceramic main bearings = $75
1/8 scale CEN tuned pipe = $60
#9
Big Block Mnt
PM sent
#10
Sorry I would rather not sell the mount seperately
the Qoncepts mounts usually go for around $60 new (whenever they are in stock) but its hard to sell a truck that one cant attach a motor to
the Qoncepts mounts usually go for around $60 new (whenever they are in stock) but its hard to sell a truck that one cant attach a motor to
#11
diffs are sold - motor anyone?
#12
just another bump