|
Originally Posted by kyosho17
(Post 8634558)
hey found the nova rod its bout $60 bucks but it was backordered i can get you the axe rossi new rod for $40. If you still want to get mamba go to the website and it will take you to paypal if you like
|
pm me
kyosho17
Pm me with your address to send these engines for refurbishment/qoute:nod: |
OK it should be there thanks alot:):)
|
Is it my imagination or is the AXE236R21 X2 Cobra slower than the AXE198R21 Cobra ? I have both engines and it seems like the original Cobra had more grunt, but then again mine had over 3 gallons and two rods before I retired it. The newer X2 just seems to barely hold in comparison? maybe it needs more time any suggestions?
|
axe cobra
Originally Posted by Twisted_Metal
(Post 8666329)
Is it my imagination or is the AXE236R21 X2 Cobra slower than the AXE198R21 Cobra ? I have both engines and it seems like the original Cobra had more grunt, but then again mine had over 3 gallons and two rods before I retired it. The newer X2 just seems to barely hold in comparison? maybe it needs more time any suggestions?
Also What restrictor are you Using? Only 3gal on a axe ENGINE????something is wrong . your tune or rod issues must have caused internal damage. most axe engines last 8+gallons, they start to come to life at 2-3 gal |
Yes I would do as blackmagic said to u could also have wrong plug,carb resictior,I run x2 on truggy got 8gal before any trouble then I just replace rod pinch it and its now a practice engine. I know when I run hotter plug mine does not have what it should they run very well with axe cold plug. Hope this helps
|
tiwisted metal
Hey twisted metal just checkin to see if u got ur x2 figured out yet
|
black magic 21
hey let me know on ur other engines if you need some help,and ive got some of the axe rods in just got my mamba broke in this last weekend and ran first race of our season with it ialmost like the mamba more than my x2's:tire::tire:
|
axe
still wating for tax funds to come in :cry:
i hope this week:nod: |
Yea I ve been runnin my mamba and been lovin it its got mor bottom than x2 been using jp2 pipe tried smaller resistior and it does well on pwr but fuel milage was down a little more 9min as compared to 10 and half with large resistior guess I was a little heavier on throttle mabe but had the best pwr all day
|
restrictors
Originally Posted by kyosho17
(Post 8763845)
Yea I ve been runnin my mamba and been lovin it its got mor bottom than x2 been using jp2 pipe tried smaller resistior and it does well on pwr but fuel milage was down a little more 9min as compared to 10 and half with large resistior guess I was a little heavier on throttle mabe but had the best pwr all day
the 6.0 did not show any improvement over the 6.5 now the 5.5 is were im getting the best fuel but there is a notable low end power loss " i'll save that for the big tracks" pipe= rdlogic's mid range pipe long header going to start testing pipes and headers:sneaky: "this weekend":nod: i will report findings and model running the blackmagic case and head with mamba x2 internals |
Longest post that i ever posted
It is AMAZING to find so much info in one place about the axe rossi motors. I was directed here by Blackmagic21 after seeing that "he is a huge fan of the black magic" (which might be an understatement), any who i too am a fan of the black magic. I got one used about 5 years ago with the purchase of a crappy wannabe Mayhem st. He said it was rebuilt and hasn't ran it much since. Well i purchased the whole package for 200.00 bucks. Let me tell ya, i justify the purchase as spending 200.00 on the motor and the mayhem st was just crap attached to it.
I ran the mayhem for a year and i couldn't control it what so ever. But man could i blow the lids off every body else in the straight away lol. Then 2 years later i put it in a buggy (losi 1.0) There again it was hard to control so i tamed it down with clutch shoes and springs. Fast forward a year and i bought a original mamba for 200.00 new before they had x models cause i liked the axe and no one else ran them. (I like to be different) The mamba was awesome right out of the box, very comparable to the black magic but not as much power it seemed which is ok still have to tame down cause of the low end is huge. Any ways i have not had problems with rod on eithier motors. have replaced bearings in the mamba for this year and everything looked fine. The black magic is collecting dust cause it is in need of a rebuild. And a carb cause one of the needles wouldn't screw out and i broke it. Also after reading this whole thread i guess my mamba is in need of a new carb also cause i followed online rossi directions to find tune and i bottomed out both needles. Any ways im looking for parts for the black magic cause i would like to use it in my new truggy (losi 2.0) and i loved the pipe that came with the black magic which is the expandable one. (name escapes me) i need the o-rings that go in the middle on the screw part of the pipe. If i can get the parts reasonable I would like to use the mamba and blackmagic this year for racing (i live in wisconsin so racing is seasonal) before i use the O.S. Speed that i bought used for 125. Sorry about the long post, just really excited to find new info on axe oh and im gonna sneek this in i have a Axe .12 X5 new in box never seen fuel just fingerprints for sale:D |
blackmagic p/s/r set
dirt devil i can get you the p/s/r for your magic for $125 and a oring set for carb is $5. If you like you can send them to me and i will rebulid them or i sendya the parts. By the way is this andrew let me know if i can help ya :tire::tire:
|
Originally Posted by blackmagic21
(Post 8777655)
i got my special order $$:cry:$$ restrictors in on fri ran saturday and sunday testing and tunning best runtime i got was 11.4min on 5.5 averaged 10.8min on 6.0-6.5
the 6.0 did not show any improvement over the 6.5 now the 5.5 is were im getting the best fuel but there is a notable low end power loss " i'll save that for the big tracks" pipe= rdlogic's mid range pipe long header going to start testing pipes and headers:sneaky: "this weekend":nod: i will report findings and model running the blackmagic case and head with mamba x2 internals |
Originally Posted by Dirt Devil
(Post 8797383)
It is AMAZING to find so much info in one place about the axe rossi motors. I was directed here by Blackmagic21 after seeing that "he is a huge fan of the black magic" (which might be an understatement), any who i too am a fan of the black magic. I got one used about 5 years ago with the purchase of a crappy wannabe Mayhem st. He said it was rebuilt and hasn't ran it much since. Well i purchased the whole package for 200.00 bucks. Let me tell ya, i justify the purchase as spending 200.00 on the motor and the mayhem st was just crap attached to it.
I ran the mayhem for a year and i couldn't control it what so ever. But man could i blow the lids off every body else in the straight away lol. Then 2 years later i put it in a buggy (losi 1.0) There again it was hard to control so i tamed it down with clutch shoes and springs. Fast forward a year and i bought a original mamba for 200.00 new before they had x models cause i liked the axe and no one else ran them. (I like to be different) The mamba was awesome right out of the box, very comparable to the black magic but not as much power it seemed which is ok still have to tame down cause of the low end is huge. Any ways i have not had problems with rod on eithier motors. have replaced bearings in the mamba for this year and everything looked fine. The black magic is collecting dust cause it is in need of a rebuild. And a carb cause one of the needles wouldn't screw out and i broke it. Also after reading this whole thread i guess my mamba is in need of a new carb also cause i followed online rossi directions to find tune and i bottomed out both needles. Any ways im looking for parts for the black magic cause i would like to use it in my new truggy (losi 2.0) and i loved the pipe that came with the black magic which is the expandable one. (name escapes me) i need the o-rings that go in the middle on the screw part of the pipe. If i can get the parts reasonable I would like to use the mamba and blackmagic this year for racing (i live in wisconsin so racing is seasonal) before i use the O.S. Speed that i bought used for 125. Sorry about the long post, just really excited to find new info on axe oh and im gonna sneek this in i have a Axe .12 X5 new in box never seen fuel just fingerprints for sale:D the pipe is the "magic one" :nod: if you want to sell it let me know:D it is a all in one pipe low to high . best pipe for a black magic been looking for one for a long time i think if you bought it on ebay i was bidding against you back then.....lol...:lol: i bid on all blackmagic engines on ebay i think i have 6 or so now and several of the hps2000 gold head engines and one silver arrow. |
| All times are GMT -7. It is currently 02:18 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.