|
Originally Posted by jeffreylin
Gordan, if your crankshaft is okay you don't need to replace it. You MAY need to replace the conrod. You can get a conrod from tower hobbies or trinity online (shopatron).
If you are coming this Sunday bring your motor and we can take a look. |
evo 111 crank
Originally Posted by Motorman
prepare to wait till hell freezes over. Just ask Ray.
On the track the engine is ballistick, have not noticed any performance difference. 3 litres of testing and engine running strong. The latest engines fom Sirio should have these cranks. Regards Alex.K |
Can I use an sirio .12 evo 2 efra crackshaft in a sirio .12 evo 2 ifmar engine? If so, how should i retune the engine? leaning or richen the HSN?
|
Originally Posted by litespeed-dom
I was real worry about the crank breaking as people has said... I got mine, broke it in (heat cycles), ran a club race, ran an entire regional, then ran another race at a permanent facility where it's designed really for 1/5th and 1/8th... Still no problem so far. I'm beginning to think it might have to do with the break-in process people are using. Or am I just the lucky few.
Anyway, it's all torn apart now, checked tolerance with nothing out of ordinary, last club race coming up so I'm just strapping in a JP instead. Dom Well, broke the crank today, 5 mins into the Main..... So what's the word on sending it to Trinity? Sure they know there is a problem with the crank! Dom |
:confused: Ive got a sirio bigblock .27, flames out toooooo much!!!! anyone here give me some advice on this?
|
Originally Posted by sniper_rc
:confused: Ive got a sirio bigblock .27, flames out toooooo much!!!! anyone here give me some advice on this?
sirios are the fastest engines i have ever seen, especially after the owner lauches the engine out of a 20 story apartment block hahahahaha :lol: :lol: :lol: :lol: |
Originally Posted by sniper_rc
:confused: Ive got a sirio bigblock .27, flames out toooooo much!!!! anyone here give me some advice on this?
But you have to describe how it die off... at slowing down or at high speed? would it die off if the truck is off the ground? :sweat: |
hey ppl, im getting to racing buggyCaster ZX-1 1/8th and need some serious suggestions on some engines that i may use, what are your thoughts on the 21 Kani evo 2? and the 21RE and what other off road sirio engine would you say is good?
|
sniper_rc id say that you should check that you tighten the glowplug properly and check for any air leaks on the engine if you havent done that already.
|
Does the Evo III use Novarossi turbo plugs? Or is it like the Picco based engines an totally different?
BB |
Originally Posted by Bundy_Bear
Does the Evo III use Novarossi turbo plugs? Or is it like the Picco based engines an totally different?
BB |
Are there still problems with the cranck of the .12 evo 3?
|
The early cranks there were some failures but the latest ones are flawless.
The EVO 3s are awsome holding their tune and pulling crazy power. I just finished running the SIRIO EVO 3 at the Aussie nationals and the engine is at least as quick if not quicker than the quickest and latest around. Infact I was in the same qualifiers as the winner (LRP) and was backing off at the end of the straight as courtesy to him so as i would not clean him up. And balls out of the corner, lots of them. Any busted cranks should be replaced by your Sirio supplier but I can guarntee that the new engines are bullet proof. Cheers Alex.K |
Have they sorted out the Evo 2 WCR Cranks yet any news on them as I have been waiting to get my engine back since the NSW State titles :flaming:
ANY!! news would be much appriciated. ANY! |
Originally Posted by kickass
Any busted cranks should be replaced by your Sirio supplier but I can guarntee that the new engines are bullet proof.
Cheers Alex.K Dom |
| All times are GMT -7. It is currently 08:12 AM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.