Serpent 960....
#2101
12X18 ceramic bearing set...
Hi guys,
yesterday i tried out the new ceramic bearing set with the light weight rear
wheel shaft with WOS spacer... the bearing bushing is not holding up... i had a slight hit at the wall... everything is OK but the bering went into the rear upright... one ring break off from the bushing... has anyone experience this b4??
is there a alluminium bushing for this part?? thanks
regards
CK
yesterday i tried out the new ceramic bearing set with the light weight rear
wheel shaft with WOS spacer... the bearing bushing is not holding up... i had a slight hit at the wall... everything is OK but the bering went into the rear upright... one ring break off from the bushing... has anyone experience this b4??
is there a alluminium bushing for this part?? thanks
regards
CK
#2102
Originally Posted by SMcpot
Would anyone know if the bodymount arms from the 960 would fit on a 950? The bodymount itself fits, but it looks like the 950 arms themselves are either too short or need to be clearanced a bit for them to work.
#2103
Tech Adept
iTrader: (1)
Originally Posted by ck960
Hi guys,
yesterday i tried out the new ceramic bearing set with the light weight rear
wheel shaft with WOS spacer... the bearing bushing is not holding up... i had a slight hit at the wall... everything is OK but the bering went into the rear upright... one ring break off from the bushing... has anyone experience this b4??
is there a alluminium bushing for this part?? thanks
regards
CK
yesterday i tried out the new ceramic bearing set with the light weight rear
wheel shaft with WOS spacer... the bearing bushing is not holding up... i had a slight hit at the wall... everything is OK but the bering went into the rear upright... one ring break off from the bushing... has anyone experience this b4??
is there a alluminium bushing for this part?? thanks
regards
CK
ck960,
#903225. I too have the lightweight rear axles on my car and the new 12x18 ceramic kit. I do not have the #903225 bushings in the rear and I am not running the WOS spacer that comes with the rear axles. No problems so far with no spacer/bushing. I am also running the quick change levers in the rear instead of the fixed nuts.
For your situation the #903225 bushings in the rear should keep your inner and outer bearings spaced out with the new 12x18 ceramic kit.
http://www.serpent.com/product/903225/
Hope this helps.
#2105
Tech Master
iTrader: (22)
Originally Posted by captian
yes it will work i have it on my 950r vector nt arm modded with 960 mount
#2106
Originally Posted by SMcpot
Sorry....are you saying you're running the Vector NT bodymount arms with the 960 bodymount on your 950? If so, are the Vector bodymount arms different from the 950's? The reason I ask is because it looks like the 950 arms are just too short and cause the suspension to bind at full droop because of this. I'm hoping that the 960, or Vector NT, arms are long enough to prevent this
This is the rear body mount arm for the 950 as well as the Vector NT. They are the same. From the 950 and the 960 the rear body mount arms are different in that they are slightly taller i believe.
I believe, if im not mistaken, the 950 bodymount arms should work with the 960 bodymount, but it may require a bit of dremel work on the bodymount and the bodymount arms as well itself for them to clear properly. It's not much, but you'd have to engineer it yourself. (Im not too sure though, but i know of racers that have done this so im just passing on information ive been told.)
Hope this helps!
#2108
Originally Posted by nigelnuggets
http://www.serpent.com/product/909342/description/
This is the rear body mount arm for the 950 as well as the Vector NT. They are the same. From the 950 and the 960 the rear body mount arms are different in that they are slightly taller i believe.
I believe, if im not mistaken, the 950 bodymount arms should work with the 960 bodymount, but it may require a bit of dremel work on the bodymount and the bodymount arms as well itself for them to clear properly. It's not much, but you'd have to engineer it yourself. (Im not too sure though, but i know of racers that have done this so im just passing on information ive been told.)
Hope this helps!
This is the rear body mount arm for the 950 as well as the Vector NT. They are the same. From the 950 and the 960 the rear body mount arms are different in that they are slightly taller i believe.
I believe, if im not mistaken, the 950 bodymount arms should work with the 960 bodymount, but it may require a bit of dremel work on the bodymount and the bodymount arms as well itself for them to clear properly. It's not much, but you'd have to engineer it yourself. (Im not too sure though, but i know of racers that have done this so im just passing on information ive been told.)
Hope this helps!
#2109
Anytime guys, always here to lend a helping hand when available!
#2110
Hi.
Where do you guys buy your spares for 960?
I'm getting sick of musrhoom already, sometimes it takes 3 weeks for the order to get here.
I need a good online store that is fast and reliable.
sn4il
Where do you guys buy your spares for 960?
I'm getting sick of musrhoom already, sometimes it takes 3 weeks for the order to get here.
I need a good online store that is fast and reliable.
sn4il
#2111
Tech Regular
iTrader: (2)
Originally Posted by sn4il
Hi.
Where do you guys buy your spares for 960?
I'm getting sick of musrhoom already, sometimes it takes 3 weeks for the order to get here.
I need a good online store that is fast and reliable.
sn4il
Where do you guys buy your spares for 960?
I'm getting sick of musrhoom already, sometimes it takes 3 weeks for the order to get here.
I need a good online store that is fast and reliable.
sn4il
www.ashfordhobby.com
#2112
Tech Regular
Can't beat Robert's "www.ashfordhobby.com" online ordering. Once you log-in (like a forum), you can order every part of every manufacture and see in real time the quantiy availlability for each item.
Then you receive the e-mail order confirmation and tracking number, which let's you see the items ordered and the tracking number to watch the package headed to your door!!
(if you've ever ordered that "must need" item the week prior to a race only to get the package and see that the one part you needed out of the 5 your ordered, is back ordered) UGH!!
Darin
Then you receive the e-mail order confirmation and tracking number, which let's you see the items ordered and the tracking number to watch the package headed to your door!!
(if you've ever ordered that "must need" item the week prior to a race only to get the package and see that the one part you needed out of the 5 your ordered, is back ordered) UGH!!
Darin
#2113
Tech Apprentice
I agree with Darin. I always have good luck when ordering parts from Ashford.
#2114
Give Kamikaze Toys and Hobbies a call! They also have the full line of parts as well as the hopups, we always do our best to keep every part in stock as well.
714-997-8697
Parts are still being uploaded into the website, so if you dont see the parts you need just give us a call!
714-997-8697
Parts are still being uploaded into the website, so if you dont see the parts you need just give us a call!
#2115
Tech Apprentice
Originally Posted by rpoage
We carry a very large slection of Serpent, Mugen, Kyosho, XRay and general racing parts. Our site is real time inventory so you will know if it's in stock or not.
www.ashfordhobby.com
www.ashfordhobby.com
It almost make me want to cry when I see the price your asking for the 960 compared to whats been asked in this country.