MTX 5
#946
Tech Elite
iTrader: (5)
If your setting up for a fuel gun hole 'directly' above the tank lid, using a cable tie to pull open the tank, then sure like Robert had at the EC with long grub screw would be fine.
But it's just the a club/test body shell, where the bulk of my refueling is going to be from a bottle, pulling the tank open with a thumb, and I did not want the hole that far onto the roof for all that, the hole I made is about 8mm onto my roof, meaning 3rd post kind of needs to be further forward.
I don't see how what I did can foul the servo saver in any way?,
But it's just the a club/test body shell, where the bulk of my refueling is going to be from a bottle, pulling the tank open with a thumb, and I did not want the hole that far onto the roof for all that, the hole I made is about 8mm onto my roof, meaning 3rd post kind of needs to be further forward.
I don't see how what I did can foul the servo saver in any way?,
#947
Tech Elite
iTrader: (32)
If your setting up for a fuel gun hole 'directly' above the tank lid, using a cable tie to pull open the tank, then sure like Robert had at the EC with long grub screw would be fine.
But it's just the a club/test body shell, where the bulk of my refueling is going to be from a bottle, pulling the tank open with a thumb, and I did not want the hole that far onto the roof for all that, the hole I made is about 8mm onto my roof, meaning 3rd post kind of needs to be further forward.
I don't see how what I did can foul the servo saver in any way?,
But it's just the a club/test body shell, where the bulk of my refueling is going to be from a bottle, pulling the tank open with a thumb, and I did not want the hole that far onto the roof for all that, the hole I made is about 8mm onto my roof, meaning 3rd post kind of needs to be further forward.
I don't see how what I did can foul the servo saver in any way?,
maybe can foul it when you turn turtle.. i dunno but i just feel not safe or right with it. Coz underneath it is the bearing..
#948
ARROWMAX Released MTX5 Spare Parts
#949
Tech Elite
iTrader: (13)
Join Date: Feb 2007
Location: Landsborough, Queensland, Australia.
Posts: 2,142
Trader Rating: 13 (100%+)
If your setting up for a fuel gun hole 'directly' above the tank lid, using a cable tie to pull open the tank, then sure like Robert had at the EC with long grub screw would be fine.
But it's just the a club/test body shell, where the bulk of my refueling is going to be from a bottle, pulling the tank open with a thumb, and I did not want the hole that far onto the roof for all that, the hole I made is about 8mm onto my roof, meaning 3rd post kind of needs to be further forward.
I don't see how what I did can foul the servo saver in any way?,
But it's just the a club/test body shell, where the bulk of my refueling is going to be from a bottle, pulling the tank open with a thumb, and I did not want the hole that far onto the roof for all that, the hole I made is about 8mm onto my roof, meaning 3rd post kind of needs to be further forward.
I don't see how what I did can foul the servo saver in any way?,
Kindest regards,
Lars.
#950
Tech Apprentice
does anybody know when it whill be available in europe the mtx5???
#951
the car is on the way to europe. should be here in the next 2 weeks.
#952
I receive mine yesterday! And I am starting to build right now!!!
#954
Tech Rookie
I got mine last monday... and i finish it yesterday... Im in Spain (europe) thanks to my asian friends!!!
#955
Nobody else had problems with the rear camber links? when I use 0 offsett wheels and 199-200mm with then only about 1-2mm treads are into the ball link, I had to get some xray links and bals that I had to get it to work.
And the button head srews are not good and to big in the hex slot.
Other then that I liked it just a lot of understeer with stock setup
And the button head srews are not good and to big in the hex slot.
Other then that I liked it just a lot of understeer with stock setup
#956
Nobody else had problems with the rear camber links? when I use 0 offsett wheels and 199-200mm with then only about 1-2mm treads are into the ball link, I had to get some xray links and bals that I had to get it to work.
And the button head srews are not good and to big in the hex slot.
Other then that I liked it just a lot of understeer with stock setup
And the button head srews are not good and to big in the hex slot.
Other then that I liked it just a lot of understeer with stock setup
#957
Tech Elite
iTrader: (5)
Anyone else notice all the different setup sheets?, the download-able one is different to the one that came in my kit, and Japan gets a different one also, I think the one with my kit also has some changes from even the build instructions.
Though now we have a Robert EC sheet and a Fukuda sheet.
Though now we have a Robert EC sheet and a Fukuda sheet.
#958