How did you leave yours stock for 7 years??? My 3906 driveshafts aka pretzelshafts were toast after like 6 months!! On factory titans!!!

Look at the many looks!! Proline use to make some sweet wheels for the maxx's back in the day!!! They make some cool ones now... But them older ones sure were spiffy!! I had some too!! I think they were called Velocity or something like that! On Mashers!! They were pre-mounts....
Just ordered the Trencher X's premounts on Desperado's for my Summit! 5lbs of wheels and tires!!! Should be interesting!! Wandering if I'll have to make a trip to my LHS for some different pinions... Being that with that much tire, I *may* need to gear down... Puttin HPI Savage Premounts on my E-maxx required gearing down... It was a dog on 18t pinions... Think I have 17t or 16t on there now...

just got done doing a flm emaxx build a while back.

parts list
flm chassis
flm hybrid bulkheads
ue shock towers
flm hinge pins
flm skids
rpm skids on top of flm
rpm arms
ofna hyper 7 diffs
proline powerstroke shocks
tekno carriers
losi xxl cvds
traxxas heavy duty tie rods
hobbyking 120 esc
turnigy motor
flm side motor mount
kershaw battery tray

The truck has taken a serious beating, i blew a outdrive cup out on the first run but then switched them to rc monster and have not had any problems. Originally had the truck on the 4 shock ue/ofna setup but switched to the pro lines and prefer that. Bent a couple hinge pins and just broke a arm but i spend most of the time at the bmx track/ freestyle jumps
http://i43.photobucket.com/albums/e3...s/IMG_0802.jpg
http://i43.photobucket.com/albums/e3...s/IMG_0793.jpg
http://i43.photobucket.com/albums/e3...s/IMG_0803.jpg
http://i43.photobucket.com/albums/e3...s/IMG_0806.jpg

I've got a ton of em!! Ton of pics for all my trucks!! But I'm offshore right now @ work... I can upload them on my PC when I fly home... Workin off an iPad right now... Lol... I arrive home on the 28th.. This wed... And I'm about to do a complete teardown/rebuild of my Summit.... So I'll have a billion pics to post then!! My maxx JUST got finished before I came out for this hitch... So it's still nice and shiny with 95% new parts!!! Haha... Only ran 1 set of batteries through it to make sure everything was in working order... Didn't even get it dirty!!!

Nice FLM MAXX moondoggie!!! I almost went the FLM route... But I knew I'd burn AT LEAST $1000 doing that!!!!

Thanks and yea they can get pretty pricey but with the hobbyking electronics it's not too bad. Also I was big into racing and sold almost all of my racing stuff and just have more fun bashing now.

Since no one has posted a Nitro version I will.

Custom 5 piece extended chassis, 15 ½ inch wheel base
GA bulkheads with custom hinge pin capture system
New Era chassis braces
Custom shock towers and limiting straps
Custom skid plates and wear plates
Custom bulkhead braces
HPI BP diffs
Custom single speed with 1/8th scale center differential transmission
Custom front and rear brakes
UE Wide Maxx a-arms
Tekno axle carriers with custom 8mm stub axles/Ofna 17mm hexes
HPI center drive shafts
All wheel shafts are UE dog bones with UE drive cups on the diffs and stub axles
Recessed Ofna violator fuel tank
Ofna shocks with custom springs and revo variable damping pistons
Custom steering bellcrank with integrated servo saver
Revo wing mount/Proline wing
Custom battery/receiver box

I’m sure I missed a few things as well

It’s only been powered by a BB engine a few times for testing.
It has been completely disassembled and all aluminum polished waiting for the new HPI gas engine to be released.

http://i280.photobucket.com/albums/k...d/DSC04397.jpg

That may be the cleanest "T-maxx" I've ever seen.... Usually they are greasy and look like the underside of an 80's model car!!! Nice truck!!

Guess I might as well add mine to the list.


-FLM E-Maxx 3905 Extended Chassis
-SuperMaxx Widetrack suspension arms
-FLM Shock towers
-FLM Ultimate Hybrid bulks Front and Rear
-FLM Skids Front and Rear
-FLM Hardened steel hinge pins
-Castle MMM and 2650kv motor
-Tekno axle carriers
-Traxxas CVDs
-Traxxas Black Tubes toe links
-Ofna Titan 1/8 shocks
-RC Screwz Stainless screw kit
-Hot Bodies Lightning wing and mount
-Traxxas 17mm adapters
-Pro-Line Mulchers on some unknown wheels
-Avid rubber sealed bearings throughout
-Turnigy Nano-Tech LiPos 35-70c 5k mAh. Pair of 2s, pair of 3s
-Spektrum DX3r
-SR3100
-Savox SC-0254mg 100 oz/in @ 0.14sec, brushless
-Gorilla Maxx battery straps

Stock items
-Emaxx BL edition trans, motor plate and gear cover
-Tmaxx steering bellcranks
-Body mounts
-pivot/pillow balls

http://i443.photobucket.com/albums/q...d/IMG_1437.jpg

I've been following your build as well!!! Just got tired of hunting down each individual one.... Figured this thread would be a good way for everyone to discuss different ideas, parts, etc..... NICE RIG BTW!!!!