Large Scale Thread....For 1/6,1/5,1/4 scale rc
#1
Large Scale Thread....For 1/6,1/5,1/4 scale rc
Sa lahat po ng may malalaking rc either 1/4,1/5,1/6 scale dito po tayo mag usap usap at magbigayan ng ideas and opinions para sa laruan nating malalaki.....
post po kayo ng pics,videos or tips......
meron po akong hpi baja 5b ss
sa lahat ng may baja 5b or 5t dito po tayo mag post na lang.... lahat po ay welcome dito yung ibang gustong magkaroon at matuto about sa large scale na baja...
post po kayo ng pics,videos or tips......
meron po akong hpi baja 5b ss
sa lahat ng may baja 5b or 5t dito po tayo mag post na lang.... lahat po ay welcome dito yung ibang gustong magkaroon at matuto about sa large scale na baja...
#2
here's a tips to beefen-up your front bulkhead in hard impact collision....
put a front lower brace chassis behind the upper rear bulkhead...instead remove the caster clip and put that chassis lower brace then you're good to go..
see pics na lang po and kapag wala kayo makuha that parts i can make one for you in a little cost made from 5-5.5mm frp. ....
put a front lower brace chassis behind the upper rear bulkhead...instead remove the caster clip and put that chassis lower brace then you're good to go..
see pics na lang po and kapag wala kayo makuha that parts i can make one for you in a little cost made from 5-5.5mm frp. ....
#3
1/6 scale Light Seal Support Craft
I still have my fiberglass molds for the 1/6 scale Vietnam LSSC (Light Seal Support Craft).
Somewhere down the road, Im thinking of powering it with a 26cc gas engine if budget permits
Running it with 6 12" Nam GI Joes would probably look cool!
Somewhere down the road, Im thinking of powering it with a 26cc gas engine if budget permits
Running it with 6 12" Nam GI Joes would probably look cool!
#4
baka malunod po yung mga gi joe....
kapag napinturahan na yung frp hull maganda na yan..
#5
sa lahat po ng gustong magbash ng baja nila punta po kayo dito sa amin may malaking open space na puede natin pag laruan..offroad...i'll try to post pic later..
that's my revo flying high.............
that's my revo flying high.............
Last edited by skuter-race-ta; 08-30-2011 at 11:27 PM.
#6
Very nice, but I prefer electric na lang sir kahit siguro yun mamba monter pwede na dyan it doesnt have to run fast baka magkahulog yun mga tao tsaka para malinis but thats me. Post video once your done sir
#7
@Skuter
Bro ilang katanungan lang
1)hich is more value for the money the SS or the RTR 2.0?
2)Di ba mahirap mag tono ng engine?
3)Meron ba parts na madali masira?
4) What can you say about the clone version? It seems to come from the very same OEM subcontracted manufacturer (except the engine).
Bro ilang katanungan lang
1)hich is more value for the money the SS or the RTR 2.0?
2)Di ba mahirap mag tono ng engine?
3)Meron ba parts na madali masira?
4) What can you say about the clone version? It seems to come from the very same OEM subcontracted manufacturer (except the engine).
#8
Yan yung motor ng grass cutter.
#9
Nope, not for racing - just running scale.
#10
sa grass cutter alam ko medyo maliit kesa sa baja...
#11
@Skuter
Bro ilang katanungan lang
1)hich is more value for the money the SS or the RTR 2.0?
2)Di ba mahirap mag tono ng engine?
3)Meron ba parts na madali masira?
4) What can you say about the clone version? It seems to come from the very same OEM subcontracted manufacturer (except the engine).
Bro ilang katanungan lang
1)hich is more value for the money the SS or the RTR 2.0?
2)Di ba mahirap mag tono ng engine?
3)Meron ba parts na madali masira?
4) What can you say about the clone version? It seems to come from the very same OEM subcontracted manufacturer (except the engine).
1)baja ss kasi 26cc na unlike sa 2.0 23cc
2)napakadali mag tono same as 2stroke principle skuter
3)walang madaling masira,except lang yung shock tower dahil prone sa roll-over pero nangyayari lang yun sa hard bashing and collision
4)for me only dika masisiyahan sa clone kasi mabagal and pangit tunog,at yung not all parts are compatible w/the original...and last sayang lang pera mo.
#12
26cc
Marami ding pond dyan banda sa inyo ah pwde ka mag try ng rc boat! Minsan dun ako nag lalaro kina Marlon aka POWERMETAL sa balangkas, valenzuela.
#13
Pero, mukang nasagot naman kayo ni sir Bongsky regarding 26cc gas engine size.
I'll attach some pics of the 26cc gas engines in rc boats..........
#14
My 5T
#15
@ricobeds...sir nice conversion sa 5t nyo yan po ba yung body na sinasabi nyo sa akin?..
ako rin tuloy ko na yung proj. kong 5t......
post ko rin pag dating ng mga parts....
ako rin tuloy ko na yung proj. kong 5t......
post ko rin pag dating ng mga parts....
Last edited by skuter-race-ta; 08-31-2011 at 08:15 AM.