Manila RC Gallery
#1546
Tech Master
the racing shell
i use this shell for racing and then the original hard plastic for show. this is the controller i use for racing. i use an 8ch one for show so i can hook lifters,wheelie bars,lights and etc.....
#1547
Tech Master
TODAY'S SPECIAL
PROJECT PURSUIT03
I HAVE ALWAYS WANTED TO DRIVE POLICE CARS.....
I HAVE ALWAYS WANTED TO DRIVE POLICE CARS.....
#1548
Tech Master
STARTED RIGHT
instead fo buying a standard TA03 kit , i went straight to buying the hop ups. if i did buy a regular kit, i would have used only 4 items from it namely rear arms,fr gear case,steering block,body mount. the rest were hop ups.
#1549
Tech Master
steering
shown is (53316) TA03 alloy racing steering with a KOpropo servo. servo is held by (53308) alloy servo stay
#1550
Tech Master
DRIVE GEARS
i first tried strantard ta03 gears(64pitch). they couldnt handle the stress. i went for the Robinson 48picth coversion and used lite alloy 18tooth pinion ofr the job. i dodnt really need them but i just had to have them. installed were (53298) Ta03f tor
#1551
Tech Master
DRIVE GEARS
i first tried strantard ta03 gears(64pitch). they couldnt handle the stress. i went for the Robinson 48picth coversion and used lite alloy 18tooth pinion ofr the job. i dodnt really need them but i just had to have them. installed were (53298) Ta03f torque control unit and (53299) ta03r torque control unit. (53291) TA03 ALLOY PULLEY WAS USED AT REAR.
#1552
Tech Master
SOLID FRONT
front arms and shock towers(fr/rr) by CROSSracing, hub carriers by TRINITY,titanium screws by HG, (53276) flouro sway bars(53266) stainless steel shafts, (53268) urethane bumpers,(53275) alloy motor heat sink
#1553
Tech Master
EVEN WEIGHT
WITH TWO IDENTICAL GEARBOX AND MOTOR, THE WEIGHT WAS SPREADOUT EVENLY. rear traction was sufficient.
53288 - alloy rear upright
53285 - rear body mount support plate
53310 - uni drive shaft(fr/rr)
53312 - carbon stab support
53288 - alloy rear upright
53285 - rear body mount support plate
53310 - uni drive shaft(fr/rr)
53312 - carbon stab support
#1554
Tech Master
G10
tekin G10 handles the output for the two perfectly matched Trinity D2 9single motor. i did the dyno myself using my Robotronics dyno and came up with 54,678rpm and [email protected]. the G10 was not meant to handle this load in a race but would handle it for 2mins at a time. tyres wont last 2 packs cos of the awesome takeoff.
NOTE: of course, the belt was not used...
53261 - pro carbon battery plate set
NOTE: of course, the belt was not used...
53261 - pro carbon battery plate set
#1555
Tech Master
not that heavy
with all of the hopups,alloy,extra motor the car is suprisingly light at just over 1.7kg.
#1556
Tech Master
how fast does it go?
now, imagine a car that weighs 1.7kg with a 9single and then imagine a car with double that power...how fast should it go?
NOTE; MOTORS WERE CONNECTED IN SERIES
NOTE; MOTORS WERE CONNECTED IN SERIES
#1557
Tech Master
COULD NOT WAIT
HAD TO OPEN THE SHED....FIRST CAR TO COME OUT IS THIS CLASSIC....I PADLOCKED THE OTHER SHED SO I DONT GET TEMPTED TO OPEN IT.
#1558
Tech Master
MUST BE A KYOSHO
I WOULDNT DARE RUN THIS SHELL COS ITS TO NICE TO GET SCRATCHED. I GOT THE HEADLIGHTS SOMEWHERE......
#1559
Tech Master
BROWN MUST KYOSHO
IT WAS A BIT NOISY WHEN I HAD IT RUNNING
#1560
mensahe...
this guy dosent like rc at all.....