What's new @ Speed Tech R/C
#2656
Tech Champion
iTrader: (3)
Re: oh yeah
Originally posted by ghoppa
Steve,
question:
for 6 cell packs I use the Integy 30amp discharger I got from you...
BUT for 12th scale (4 cell) "What discharger do I use??" (& can I get this from you?????)
let me know!!!
Steve,
question:
for 6 cell packs I use the Integy 30amp discharger I got from you...
BUT for 12th scale (4 cell) "What discharger do I use??" (& can I get this from you?????)
let me know!!!
#2658
Tech Master
iTrader: (63)
Re: Re: oh yeah
Originally posted by RC Driver Gary
You can use the same discharger. The cutoff will be a little high, but if you can change the cutoff take it from 5.4v down to 3.6V. If not then just pull it off when its done and throw it on a good discharge tray, such as the Smart Tray.
You can use the same discharger. The cutoff will be a little high, but if you can change the cutoff take it from 5.4v down to 3.6V. If not then just pull it off when its done and throw it on a good discharge tray, such as the Smart Tray.
I was getting a lil' "nervous"......
#2659
Originally posted by AZ_Ron
Hi Steve... needing to see if you have or can get a couple of low profile hub kits for the R2/R3 series cars?? I didn't realize when I got them that you can't run 28mm foams on them with the kit parts...If you have them, what's the cost on the parts I'd need to convert two cars?
Thanks!
Ron
[email protected]
Hi Steve... needing to see if you have or can get a couple of low profile hub kits for the R2/R3 series cars?? I didn't realize when I got them that you can't run 28mm foams on them with the kit parts...If you have them, what's the cost on the parts I'd need to convert two cars?
Thanks!
Ron
[email protected]
We are currently out of stock on the low profile hubs, and I'll have to check if either Alex sells them separately or SpeedWay Pal still produce them. I think the hubs are around $36 for the front pair and around the same for the rear. You'll also need two of the drop down graphite camber link mounts to retain proper suspension geometry ($12 each, you need two) so it's about $100 to do each car.
Steve Wang
#2660
Re: 3.0 & Legacy Bodies
Originally posted by ghoppa
Steve,
just wanted to follow-up and make sure you received the information I e-mailed you......
This should take care of the the 2 3.0 Status bodies and the only Tamiya Legacy body you held for "me"....
thanks as always!
ghoppa........
Steve,
just wanted to follow-up and make sure you received the information I e-mailed you......
This should take care of the the 2 3.0 Status bodies and the only Tamiya Legacy body you held for "me"....
thanks as always!
ghoppa........
it was shipped out to you today
Steve Wang
#2661
Originally posted by k_bojar
Should have posted this the other day...was showing up "out of stock"
Should have posted this the other day...was showing up "out of stock"
I'm not sure when you checked the link, but when I posted my response, I checked for you if there were any LW suspension conversion left (and there were at least one available at the time of my posting) I'm sorry that you missed it Next shipment should be in about 1 week-10 days
Steve Wang
#2662
Originally posted by rayhuang
Steve-eta on Futaba S9550 servos?
Thanks,
Ray
Steve-eta on Futaba S9550 servos?
Thanks,
Ray
I'm sorry, we don't have any ETA on the servo at the moment.
Steve Wang
#2664
Re: order 11486
Originally posted by flysti
hi steve,
just wanting to know if you have shipped my order
thanks
hi steve,
just wanting to know if you have shipped my order
thanks
Steve Wang
#2665
Tech Regular
Steve,
Will you be getting any of the new magnesium heatsinks from Yokomo? Can i have a time when you will be getting spools in for the SD as i need to get a shipping quote from you nearer the time.
Will you be getting any of the new magnesium heatsinks from Yokomo? Can i have a time when you will be getting spools in for the SD as i need to get a shipping quote from you nearer the time.
#2666
Tech Champion
iTrader: (30)
Originally posted by SpeedTech
k_bojar,
I'm not sure when you checked the link, but when I posted my response, I checked for you if there were any LW suspension conversion left (and there were at least one available at the time of my posting) I'm sorry that you missed it Next shipment should be in about 1 week-10 days
Steve Wang
k_bojar,
I'm not sure when you checked the link, but when I posted my response, I checked for you if there were any LW suspension conversion left (and there were at least one available at the time of my posting) I'm sorry that you missed it Next shipment should be in about 1 week-10 days
Steve Wang
I ordered several things for you over the last couple of years, so I'm not gonna sweat 1 little thing Actually, you'll probably be seeing another order shortly
#2667
Steve,
Can you please help me out here with what's happening with order #11553
I placed it on the 30/1 and it never went out yesterday
I really need that stuff fast so i mailed you yesterday and got no answer and also left a message on the customer services page that you haven't answered even though i can see you've been answering other posts since else where on the forums
Please i really need the stuff, but would also like to know whats going on ??
Cheers
Rod Mingo
Can you please help me out here with what's happening with order #11553
I placed it on the 30/1 and it never went out yesterday
I really need that stuff fast so i mailed you yesterday and got no answer and also left a message on the customer services page that you haven't answered even though i can see you've been answering other posts since else where on the forums
Please i really need the stuff, but would also like to know whats going on ??
Cheers
Rod Mingo
#2668
Oh i've even tried calling a few times but can only get through to your answering machine saying everyones bussy (not your fault i know) but i would really appreciate a mail or some thing just letting me know whats going on !
Thanks
Thanks
#2669
Yay,
Managed to get through and it seems it all went out yesterday.
So great work steve and thanks again !!
Rod Mingo
Managed to get through and it seems it all went out yesterday.
So great work steve and thanks again !!
Rod Mingo