Ofna Ultra GTP2e
#1066
Tech Rookie
#1067
Tech Regular
iTrader: (10)
Front Tire Wear
Trying out a new tire manufacture running 45 shore (front/rear). The rears look spotless but the fronts do not have an even wear pattern and the outside of the tire looks like I am overheating it.
Do I need more camber in the front end?
Softer spring (currently running yellow)?
Harder Front Tire 50 shore?
Do I need more camber in the front end?
Softer spring (currently running yellow)?
Harder Front Tire 50 shore?
#1068
Tech Rookie
Getting warm yes, but that's when they get sticky. How's the traction?
#1070
Tech Adept
SNR recommends black stock front springs and no swaybar
#1071
Tech Rookie
#1072
Tech Regular
iTrader: (10)
Found the front spring had collapsed by 4mm compared to a new in package one. The front ride height was less than 7mm which would transfer the majority of the weight permanently to the back tires.
I didn't have another yellow to put back in so I went with a new white spring. Increased the front droop by .5mm, and softened the front sway bar.
Will give it a test and see if the front end slides as much and how the tires wear.
Last edited by Capt'N_Slow; 09-16-2011 at 06:40 AM.
#1073
Tech Master
iTrader: (43)
HERES A NEW VIDEO
some new sweep 55 shore slicks bashing !
THANKS igt hobbies !!
http://www.youtube.com/watch?v=ozlkYRLgz5A
some new sweep 55 shore slicks bashing !
THANKS igt hobbies !!
http://www.youtube.com/watch?v=ozlkYRLgz5A
#1074
HERES A NEW VIDEO
some new sweep 55 shore slicks bashing !
THANKS igt hobbies !!
http://www.youtube.com/watch?v=ozlkYRLgz5A
some new sweep 55 shore slicks bashing !
THANKS igt hobbies !!
http://www.youtube.com/watch?v=ozlkYRLgz5A
No Problem, Thanks.
Those tire marks on the pavement are bad ass!
#1075
Tech Regular
iTrader: (10)
Need another GTP2
Hit something square and concrete at 85mph. I have never seen a 6S lipo accordion before or a drive shaft bent this badly .
My need for speed has died down a bit. Will have to pick through the carcass to find anything not broken.
My need for speed has died down a bit. Will have to pick through the carcass to find anything not broken.
Last edited by Capt'N_Slow; 09-19-2011 at 07:59 PM.
#1076
Tech Rookie
I have assigned speed runs to better and better locations over time. A 9lb object @ 85mph needs a ton of width length to be safe from objects that just JUMP out at you! lol
#1077
Tech Regular
iTrader: (10)
Force
Weight of car = 7 lb = 31.1281 N
Mass = W / g = 7 lb / 32 ft/s^2 = 0.21875 slugs
Velocity = 85 mi/hr = 124.67 feet per second
Initial Kenetic Energy
Kenetic Energy = 1/2 ( 0.21875 slugs ) ( 124.67 ft/s )^2
KE = 1699.9728 ft lb
Stopping Distance = 8 inches
Work Required to stop the car:
Favg (d) = -1/2mv^2
Favg = 1.268875 tons (2537.75 lbs)
My 7 lbs car became 2537.75 lbs when it hit concrete? Is this right?
Mass = W / g = 7 lb / 32 ft/s^2 = 0.21875 slugs
Velocity = 85 mi/hr = 124.67 feet per second
Initial Kenetic Energy
Kenetic Energy = 1/2 ( 0.21875 slugs ) ( 124.67 ft/s )^2
KE = 1699.9728 ft lb
Stopping Distance = 8 inches
Work Required to stop the car:
Favg (d) = -1/2mv^2
Favg = 1.268875 tons (2537.75 lbs)
My 7 lbs car became 2537.75 lbs when it hit concrete? Is this right?
Last edited by Capt'N_Slow; 09-21-2011 at 10:28 AM.
#1078
#1079
#1080
Hey Transformers!!! Great looking lid. I recommend you apply a little shoe goo under the leading edge of your front end of your lid. It will make it last a little longer. Just my. 02.