Kinetix RC Batteries
02-20-2005, 10:40 AM
#286
Tech Addict
iTrader: (4)
Join Date: Feb 2002
Location: Getting practice 1/10 stock onroad
Posts: 670
Trader Rating: 4 (100%+)
GP3300STAGE1
1.15+ 30amp 6cell
$29.95
wat happen to these i never see them on your site nymore Ron?
Steven Alexander
1.15+ 30amp 6cell
$29.95
wat happen to these i never see them on your site nymore Ron?
Steven Alexander
02-20-2005, 03:46 PM
#288
Tech Addict
iTrader: (4)
Join Date: Feb 2002
Location: Getting practice 1/10 stock onroad
Posts: 670
Trader Rating: 4 (100%+)
batts
so your'e only doing 3600s or?
02-20-2005, 04:31 PM
#290
Tech Addict
iTrader: (4)
Join Date: Feb 2002
Location: Getting practice 1/10 stock onroad
Posts: 670
Trader Rating: 4 (100%+)
prices
What wil be the prices be on the 3600s? Are u making it to Mikes for the state carpet race on March 11th. By the way its Steven Alexander from shreveport(i am the black kid,but thats grown up now), you came down to race at the rutherford house with Tom Robertson and others. good luck with the batts
03-01-2005, 06:40 PM
#298
IBC3600 packs are in.
IBC3600
http://www.kinetixrc.com/catalog/pro...products_id=61
360+ run time / 1.160+ voltage
They are matched at 35 amps
Matching at 35 amps seems to weed out the weeker cells
If you are trying to compare #'s to 30 amp here are some general guidelines:
35Amp to 30amp
*Voltage add about .015v Example 1.160v @35amp = 1.175 @ 30amp
*Runtime = runtime x 35 divided by 30 Example A cell that is 360 seconds @ 35amps would be 420 seconds @ 30amp.
*Internal resistance from 35 to 30 you subtract about .1 A 2.3 @ 35amp would be about 2.2 @ 30amp
Are you fed up with not having enough power or dumping before the race is even over? Than you are at the right place, Kinetix RC offers superb quality matching that only most Team Drivers get to appreciate at a price that is lower than all the competition. Each cell is zapped to increase the numbers permenantly which is than followed by 3 cycles to ensure the numbers are accurate.
Atomic Ron (Owner of Kinetix RC) has been proving the quality of his matching by placing in the top 3 of every national stock race in 2002.
http://www.kinetixrc.com/catalog/pro...products_id=61
360+ run time / 1.160+ voltage
They are matched at 35 amps
Matching at 35 amps seems to weed out the weeker cells
If you are trying to compare #'s to 30 amp here are some general guidelines:
35Amp to 30amp
*Voltage add about .015v Example 1.160v @35amp = 1.175 @ 30amp
*Runtime = runtime x 35 divided by 30 Example A cell that is 360 seconds @ 35amps would be 420 seconds @ 30amp.
*Internal resistance from 35 to 30 you subtract about .1 A 2.3 @ 35amp would be about 2.2 @ 30amp
Are you fed up with not having enough power or dumping before the race is even over? Than you are at the right place, Kinetix RC offers superb quality matching that only most Team Drivers get to appreciate at a price that is lower than all the competition. Each cell is zapped to increase the numbers permenantly which is than followed by 3 cycles to ensure the numbers are accurate.
Atomic Ron (Owner of Kinetix RC) has been proving the quality of his matching by placing in the top 3 of every national stock race in 2002.
03-01-2005, 06:41 PM
#299
19 Turn C2's are in.
C2 based 19 turn
http://www.kinetixrc.com/catalog/pro...products_id=54
The motors are dyno tuned using a Robitronics Dyno with print out included in each motor.
High performance motor brushes used for maximum performance.
No need to break the motor in ,it has been done
Magnets zapped to center poles to perfection and insure the stongest can possible.
Armatures shimmed to center of magnetic field.
Brush hoods aligned for perfectly square brush contact.
Armatures trued with a diamond bit lathe.
Springs tested and tweeked for best performance.
Bearings pressed and checked for minimum resistance
http://www.kinetixrc.com/catalog/pro...products_id=54
The motors are dyno tuned using a Robitronics Dyno with print out included in each motor.
High performance motor brushes used for maximum performance.
No need to break the motor in ,it has been done
Magnets zapped to center poles to perfection and insure the stongest can possible.
Armatures shimmed to center of magnetic field.
Brush hoods aligned for perfectly square brush contact.
Armatures trued with a diamond bit lathe.
Springs tested and tweeked for best performance.
Bearings pressed and checked for minimum resistance