BMI Racing "Copperhead 12" discussion and support
#1038
Hey Guys,
I just finished making some optional standoffs for under the hinge pin block for high bite. Pretty much, it is 2mm taller than the stock ones. They are threaded standoffs. A set screw now will go into the pivot ball, the standoff threads onto the set screw and then you hold the hinge pin block on by threading the 2 4-40 screws into the standoffs. I figured it would be a nice option for those who want to shim high without stacking a bunch of shims. The new standoff kit will include the standoffs,2 4-40 x 5/16 set screws and 2 4-40 x 1/4 flathead screws. I will get them on the website today or tomorrow.
I just finished making some optional standoffs for under the hinge pin block for high bite. Pretty much, it is 2mm taller than the stock ones. They are threaded standoffs. A set screw now will go into the pivot ball, the standoff threads onto the set screw and then you hold the hinge pin block on by threading the 2 4-40 screws into the standoffs. I figured it would be a nice option for those who want to shim high without stacking a bunch of shims. The new standoff kit will include the standoffs,2 4-40 x 5/16 set screws and 2 4-40 x 1/4 flathead screws. I will get them on the website today or tomorrow.
#1039
#1040
Hey Guys,
I just finished making some optional standoffs for under the hinge pin block for high bite. Pretty much, it is 2mm taller than the stock ones. They are threaded standoffs. A set screw now will go into the pivot ball, the standoff threads onto the set screw and then you hold the hinge pin block on by threading the 2 4-40 screws into the standoffs. I figured it would be a nice option for those who want to shim high without stacking a bunch of shims. The new standoff kit will include the standoffs,2 4-40 x 5/16 set screws and 2 4-40 x 1/4 flathead screws. I will get them on the website today or tomorrow.
I just finished making some optional standoffs for under the hinge pin block for high bite. Pretty much, it is 2mm taller than the stock ones. They are threaded standoffs. A set screw now will go into the pivot ball, the standoff threads onto the set screw and then you hold the hinge pin block on by threading the 2 4-40 screws into the standoffs. I figured it would be a nice option for those who want to shim high without stacking a bunch of shims. The new standoff kit will include the standoffs,2 4-40 x 5/16 set screws and 2 4-40 x 1/4 flathead screws. I will get them on the website today or tomorrow.
to avoid the usual questions, i swapped upper arms and lower arms to identify the source of the caster variation, and i ended up tracing to the upper hinge fitting getting clocked when tightening it down.
#1041
Tech Champion
#1045
Here's a picture of my CH12 equipped with a...
- Graupner DES 676BB servo
- GM Genius 75 esc
- Spektrum SR3500 receiver
- Graupner LiFe 200Mah RX-pack
- Intellect 5600 / 50C LiPo
- GM Pro Stock 13.5 motor
- Graupner DES 676BB servo
- GM Genius 75 esc
- Spektrum SR3500 receiver
- Graupner LiFe 200Mah RX-pack
- Intellect 5600 / 50C LiPo
- GM Pro Stock 13.5 motor
#1047
#1048
#1050
Lightning fast!!!
Went from laptimes of 10,9sec. to 5,8sec. with these pinions... They are incredible and run really smooth!!!
Went from laptimes of 10,9sec. to 5,8sec. with these pinions... They are incredible and run really smooth!!!