1LikesAtomic VM2 M-Class Chassis
06-02-2011, 12:41 PM
#181
The word is "lose" not "loose" Mr. H. 
06-04-2011, 11:19 PM
#183
Tech Initiate
06-04-2011, 11:58 PM
#185
Tech Initiate
ahh! i guess i have to keep waiting and dreaming. btw, I shall have those special lipo for u soon. waiting for next shipment. u want then in deans or bullets?
07-12-2011, 08:39 PM
#187
Atomic VM2
Hye Guys,
Just want to let you guys know that I've just received my VM2 kit this morning. Kind of excited and cant wait to build it tonight. I also bought the Alu. center pulley and the sway bar set. =)
http://imageshack.us/photo/my-images...mage013ve.jpg/
http://imageshack.us/photo/my-images...mage012cn.jpg/
Btw, thanks for the Advice and Tips. Hope we can share more setup setting and others. =D
Just want to let you guys know that I've just received my VM2 kit this morning. Kind of excited and cant wait to build it tonight. I also bought the Alu. center pulley and the sway bar set. =)
http://imageshack.us/photo/my-images...mage013ve.jpg/
http://imageshack.us/photo/my-images...mage012cn.jpg/
Btw, thanks for the Advice and Tips. Hope we can share more setup setting and others. =D
07-15-2011, 11:39 AM
#188
Rim
Hey guys, need some info. can this kit use the normal 1/10 touring rim? has any one tried it? photos would be great.
Thanks in advance.
Thanks in advance.
08-31-2011, 12:13 PM
#190
Help:Need some opinion and suggestion.
after looking over my VM2 one more time I see the following modifications:
A. Upper suspension links (each)
1- XRay 302664 - T2 Ball Joint 5mm Unidirectional ; these are the parts with the 'dot' on them. i've used them on the inside upper camber links.
1- Team Associated TC5 Short (height) ball studs - 8mm or 10mm length (cannot remember) for use at the c-hub or rear hub
1- 3mm set screw - unknown length - to replace the turnbuckle
1- Team Associated ASC7230 T4/B3/T3 BALL END CUPS (12) - i cut these ball ends in order to make the link short enough to put 1-2 degrees of negative camber into the suspension. i rather cut these ends as they are cheap compared to the xray ones.
B. Steering Links (each)
1- Team Associated TC5 Short (height) ball studs - 5mm for use at the the steering knuckle
1- Team Associated ASC7230 T4/B3/T3 BALL END CUPS (12) - at the steering knuckle
1- kit turnbuckle
1- kit rod end
C. Shocks
1- 3mm x 10mm (i think) cap head screw to replace the grub screws holding the bottom on the shock ends to the lower suspension car
D. Front Spool
2 - XRay 305135 - T2'008 Composite Solid Axle Driveshaft Adapters (2) - to replace the Atomic Stock Units
E. Rear Diff
1 - XRay 34tooth diff from my old T2'008 - only swapped this unit in after the kit original diff screw broke
A. Upper suspension links (each)
1- XRay 302664 - T2 Ball Joint 5mm Unidirectional ; these are the parts with the 'dot' on them. i've used them on the inside upper camber links.
1- Team Associated TC5 Short (height) ball studs - 8mm or 10mm length (cannot remember) for use at the c-hub or rear hub
1- 3mm set screw - unknown length - to replace the turnbuckle
1- Team Associated ASC7230 T4/B3/T3 BALL END CUPS (12) - i cut these ball ends in order to make the link short enough to put 1-2 degrees of negative camber into the suspension. i rather cut these ends as they are cheap compared to the xray ones.
B. Steering Links (each)
1- Team Associated TC5 Short (height) ball studs - 5mm for use at the the steering knuckle
1- Team Associated ASC7230 T4/B3/T3 BALL END CUPS (12) - at the steering knuckle
1- kit turnbuckle
1- kit rod end
C. Shocks
1- 3mm x 10mm (i think) cap head screw to replace the grub screws holding the bottom on the shock ends to the lower suspension car
D. Front Spool
2 - XRay 305135 - T2'008 Composite Solid Axle Driveshaft Adapters (2) - to replace the Atomic Stock Units
E. Rear Diff
1 - XRay 34tooth diff from my old T2'008 - only swapped this unit in after the kit original diff screw broke
Hye guys,
I have a plan to upgrade my VM2 using the 3racing parts. especially the weak parts of vm2 kit that had been claim by several people. so here are the list of what I'm going to purchase. but before that I really need some feedback about the part whether its fit or not.
A. Upper suspension links (each)
1- XRay 302664 - T2 Ball Joint 5mm Unidirectional ; these are the parts with the 'dot' on them. i've used them on the inside upper camber links.
-http://www.myrcstation.com/webshaper...oductItem=3178
1- Team Associated TC5 Short (height) ball studs - 8mm or 10mm length (cannot remember) for use at the c-hub or rear hub
-http://www.myrcstation.com/webshaper...oductItem=2463
1- 3mm set screw - unknown length - to replace the turnbuckle
- no problem
1- Team Associated ASC7230 T4/B3/T3 BALL END CUPS (12) - i cut these ball ends in order to make the link short enough to put 1-2 degrees of negative camber into the suspension. i rather cut these ends as they are cheap compared to the xray ones.
-http://www.myrcstation.com/webshaper...oductItem=2900
B. Steering Links (each)
1- Team Associated TC5 Short (height) ball studs - 5mm for use at the the steering knuckle
-http://www.myrcstation.com/webshaper...oductItem=2471
1- Team Associated ASC7230 T4/B3/T3 BALL END CUPS (12) - at the steering knuckle
-http://www.myrcstation.com/webshaper...oductItem=2901
1- kit turnbuckle
-http://www.myrcstation.com/webshaper...oductItem=2953
1- kit rod end
-http://www.myrcstation.com/webshaper...oductItem=4176
C. Shocks
1- 3mm x 10mm (i think) cap head screw to replace the grub screws holding the bottom on the shock ends to the lower suspension car
-no idea
D. Front Spool
2 - XRay 305135 - T2'008 Composite Solid Axle Driveshaft Adapters (2) - to replace the Atomic Stock Units
-Next upgrade
E. Rear Diff
1 - XRay 34tooth diff from my old T2'008 - only swapped this unit in after the kit original diff screw broke
-Next upgrade
Btw, this is my car.
Thanks in Advance
taff
09-20-2011, 01:43 PM
#192
09-27-2011, 12:14 PM
#195
