Can I get the interface for a Mac? I need to download the "blinky" software. I have no PC's available.

Any day now...just waiting on approval to share code and FB ad.



SP doesn't officially say we follow this thread. I feel for everyone or anyone that has had issues with customer service. It is not my role, but I can try to help with any RMA or return issues. Just PM me. I'm not on RCtech much, but I can see what, if anything, I can do for you.

I have one 13.5 speed passion club spec system ive had for a while its still going
and the bearings are still working in it. It came in my Durango ready to run buggy.
I have used it onroad and offroad but mostly onroad.
Right now the speed passion system is in my B4.1 latemodel which is a dirt oval car.

YGPM

Where can I purchase a replacement lower half or complete case for a Gran Turismo Pro Stock 2.1 ESC? (Black)

I'm not gonna bother with that RMA issue because this was over year ago I sent many private messages on this site and to speed passion it's just a lost cause and just a loss for me so I really don't care anymore.

Has anyone noticed their motor overheating with the stock firmware. I updated to this firmware And when I was running it, motor temperatures were really high never changed gearing, no timing etc. with my previous speed controller I never had this problem should I run a different firmware?

I'm running the stock firmware with a g2 HW 6.5T motor. After a race it's only 40 degrees Celsius but I'm running a fan behind it. Also FDR is close to 11. Air temp at the time was about 21 degrees Celsius

My pro 1.1 is having cogging issues.:flaming:
put in a team powers 21.5 and cogggggggg right after netural.
did all the usual stuff swap this and that. no luck
worked fine with my sp mmm 21.5.
put that back in and now that cogs too...wierd
3 sensorwires....12+ reprogram/reset....im done:flaming:

5/13 update....had a bad sensor board in both motors, sp had a loose pin on the board. put in a new one good to go, TP had a cracked chip on the board.
no more cogging....

I got mine straight from the US seller for SpeedPower.

That sucks. I had planned on sending in my 1.1 but to what end? The Reventon R I used at the MHIC worked awesome.

Same... Numerous motors/sensor wires... Assuming you are getting a blinking red light?

Yup:mad:
ok so i went to orion and hobbywing. both use the same software but the hw is more adjustable. r10 pro and r10stock.and v3.1
hw v3.1 is my fav:nod: hw rules in mybook now:D
you can download the hw software b4 u buy and run it in demo mode and you will freak:eek: its that good

I hope SP comes out with some new stuff cause I love their stuff when it works:nod::nod::nod:

Ihave a 21.5 v4 coming :tire::tire::tire:to test out
:nod:

(Sorry for "cross-posting", but the SP thread in offroad is DEAD)

I seem to have a problem with my Reventon Pro (not the 1.1 model)... It has gotten "soft" on the bottom end - no "grunt"... The first noticable effect is that the motor runs really HOT because it has no bottom end and loads up and overheats... I tried gearing WAY-way down (5 teeth) and the motor cools off, but at the cost of huge loss of overall speed, and worst of all, there still isn't much bottom end power... The effect gets worse during a run - jumps that can be cleared early in the race become impossible later in the run... Tried different motors - it isn't the motor...

Any ideas or suggestions...? It worked great for several months (running it with a 10.5 motor in Mod Truck offroad), then the motor started running hot and the bottom end went soft... Thought it was the motor, swapped it out for a new one... Not the motor...

PS: WTF is going on with Speed Passion's software... My computer screams about malware in the Reventon software download - and my antivirus flags the entire web site as "Dangerous"...

MY Reventon interface is now dead because the removal of the malware disabled it...

Now I have 3 Reventon ESC's that I cannot update, etc... WTF?

.

http://www.rctech.net/forum/14390670-post12998.html