Originally Posted by Solara (Post 9071842)

V1.36 released
............and we are not going to support V1.35 anymore and thats why I removed the old version, and I will remove all the previous old version cause all the software we had so far are be found in the new V1.36

Stop using 1212 as this is not even close compare to the new 323STOCK software. Also, try the new 119MOD supercharger software for MOD motor.

Here is the link....you guys will love it. Make sure read the attached PDF file as this Supercharger improvement is alittle different then the previous 1.35 or 1.33 version.

http://www.speedpassion.net/us/escsetup.asp

I am in the middle of creating some setup for 17.5 13.5 motor...as well as some 8.5 10.5 for mod...all are using 323STOCK software (YES, 323STOCK software for MOD racing)...and mainly in OFF ROAD setup, but I have some on road indoor and outdoor setup as well....stay tuned.

Also, new 323stock and 119mod setup sheet....

http://www.speedpassion.net/files/Sp...k_6may2011.pdf

IMPORTANT: You must update the LCD programmer from the 1.36 version before you can see the changes for the 323STOCK, it is a must do process.

Originally Posted by vafactor (Post 9097543)

does anyone know of a US outlet that has one of the LCD speedo programming boxes in stock? Everywhere I've looked online lists them as out of stock or on back order.

Originally Posted by Raul Garcia (Post 9098298)

Is there any changes to Blinky Mode?

Originally Posted by Raul Garcia (Post 9098298)

Is there any changes to Blinky Mode?

Originally Posted by Craig W (Post 9096537)

There are out of stock

Originally Posted by sidecarphil1 (Post 9100885)

dont need brakes in 0 timing mode , dont brake :lol::lol::lol:

i have my brakes at 50% on my transmitter and 100% in the speedo but this is only incase of emergencys :sneaky::sneaky:

Originally Posted by vafactor (Post 9097543)

does anyone know of a US outlet that has one of the LCD speedo programming boxes in stock? Everywhere I've looked online lists them as out of stock or on back order.

Originally Posted by moggy12 (Post 9104422)

i tried the latest speedpassion firmware/software on my xray t3 last night had great speed out of corners but top end was not that good running fdr 7
v3 13.5 motor was set on 0 degrees so changed this to full 10 degrees what a difference so was so much faster down the straight well done speedpassion at last i have a car that can keep up with the leaders

Originally Posted by Solara (Post 9106123)

Never 0* on V3 motor...at least, I never use 0*, always 10*. And you guys have not try these bad boys yet....

http://www.speedpassion.net/us/produ...SP000034&c=OPT

http://www.speedpassion.net/us/produ...SP000029&c=OPT

http://www.speedpassion.net/uploadfi...000034-r01.jpg

http://www.speedpassion.net/uploadfi...000029-r03.jpg

Originally Posted by gdcopbdcop (Post 9106362)

When will they be available for purchase?
:)

Originally Posted by Solara (Post 9106387)

I was told next week.....at SP USA website.

Originally Posted by sidecarphil1 (Post 9095336)

ok heres my starting softwere
6.5SPv3 middle timing
drag brake 20%
DDRS lvl 3(low grip dusty track)
boost timing 36 degrees
Turbo open time 6degree/0.1sec
turbo 15 dergees
boost start rpm 10,000
turbo open delay 0.4sec
boost timing acc 500rpm/deg
Gearing 7.2