Awesomatix EP Touring Car (A700 Shaft Drive)
#6946
#6947
First limited batch ready !
#6948
New chassis with innovative features for 1/10 EP under development !
Last edited by ropezz; 08-19-2014 at 10:44 AM.
#6950
It is ideal for Hudy set up tool.
Regarding other brands of set up tools, consider that Caster tool has 0,5 mm clearance with Hudy scale (see 1° picture for reference).
Also Caster tool sits aligned with Hudy set up tool, without adding shims for track width (see 2° picture for reference).
Regarding other brands of set up tools, consider that Caster tool has 0,5 mm clearance with Hudy scale (see 1° picture for reference).
Also Caster tool sits aligned with Hudy set up tool, without adding shims for track width (see 2° picture for reference).
#6951
I am building my car with C01-AL-S and AM30-5 but I don't know which screw I have to put on AM30-5 to have a good flex starting set-up...
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
#6952
Tech Lord
iTrader: (32)
Anybody tried using this in the AMX?
http://www.liverc.com/news/new_produ...ss_motor_line/
Does it interfere with the chassis? It can only stick out the side at a right angle to the solder tabs. It replaces the center ring, so no motor scratching or sliding or other movement.
http://www.liverc.com/news/new_produ...ss_motor_line/
Does it interfere with the chassis? It can only stick out the side at a right angle to the solder tabs. It replaces the center ring, so no motor scratching or sliding or other movement.
#6953
I am building my car with C01-AL-S and AM30-5 but I don't know which screw I have to put on AM30-5 to have a good flex starting set-up...
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
#6954
R/C Tech Elite Member
iTrader: (28)
I am building my car with C01-AL-S and AM30-5 but I don't know which screw I have to put on AM30-5 to have a good flex starting set-up...
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
#6955
I am building my car with C01-AL-S and AM30-5 but I don't know which screw I have to put on AM30-5 to have a good flex starting set-up...
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
Do I have to screw all the holes on AM30-5, putting set screw (in this case, what king of?) or else? Can someone help me?
Thanks in advance,
Best regards,
G-rem
Note, be careful with the length of the screws that hold AM-49. The screws need to be very short. If they are too long the screws will run into AM30-5 and cause AM30-5 to bend away from the chassis or deform the chassis.
Jake
#6956
Team EAM
iTrader: (79)
Anybody tried using this in the AMX?
http://www.liverc.com/news/new_produ...ss_motor_line/
Does it interfere with the chassis? It can only stick out the side at a right angle to the solder tabs. It replaces the center ring, so no motor scratching or sliding or other movement.
http://www.liverc.com/news/new_produ...ss_motor_line/
Does it interfere with the chassis? It can only stick out the side at a right angle to the solder tabs. It replaces the center ring, so no motor scratching or sliding or other movement.
Just kidding. The D4 just requires some different setup to get it to run Ive heard. I just havent figured it out because Ive spent more time on my car than my motor program so far!
EA
Last edited by EAMotorsports; 08-21-2014 at 10:51 AM.
#6957
Although I have not put my C01-AL-S on the track yet, but considering how flexy it is, yeah, what Hanulec said " All screws but first and last " Also, if you have the top deck try it too since it is easy to remove.
Note, be careful with the length of the screws that hold AM-49. The screws need to be very short. If they are too long the screws will run into AM30-5 and cause AM30-5 to bend away from the chassis or deform the chassis.
Jake
Note, be careful with the length of the screws that hold AM-49. The screws need to be very short. If they are too long the screws will run into AM30-5 and cause AM30-5 to bend away from the chassis or deform the chassis.
Jake
Understood for AM49, nice tip
I'll try it first on a large low grip asphalt track with the C21 top deck, then I'll try it on carpet but I was told C01-AL would be better suited...I will see when I try.
G-rem
#6958
Anybody tried using this in the AMX?
http://www.liverc.com/news/new_produ...ss_motor_line/
Does it interfere with the chassis? It can only stick out the side at a right angle to the solder tabs. It replaces the center ring, so no motor scratching or sliding or other movement.
http://www.liverc.com/news/new_produ...ss_motor_line/
Does it interfere with the chassis? It can only stick out the side at a right angle to the solder tabs. It replaces the center ring, so no motor scratching or sliding or other movement.
#6960
If it was me I would start with a softer setting(say half screws) for aspahlt and add screws if you feel the car is too stuck and lazy. For carpet I would do all but the first and last as hanulec suggested