|
Originally Posted by gansei
(Post 4267672)
i got second position in Korea Kyosho Cup.
i realized the importance of Batteries!! E4, LRP 4.0, LRP TC, Much-More AT32 Tire, IB 4600 Zapping 6 Cell. in this circuit.. Korea Nation EP race will be held in next month the race rule of battery is only 5-cell. |
Just ordered me a 503002-C1 - 1/10 E4FS/C1 Rubber Tire Spec Electric Touring Car. It's the E4FS Rubber Conversion with (convertable) front 1 way option.
I plan on running it on a large outdoor asphalt track. http://www.rcpikeriver.com/images/rcprtrackviewbig.gif Also will have the following setup on the car: - Mamba Max with 7700 BL motor (equivalent to 7T) - Orion 4800 Lipo - 110T spur 64 pitch - Internal ratio is 2.0588 - Tires are Jaco greens (Rubberz) My question is what size of pinion should I be using ? Any suggestion on color springs to use ? I ordered the G4 spring set. Also running with a Mazda 6 Blitz body. Look forward to some help here :) |
Congrats Gansei! Any race footage?
|
Congratulations, Gansei. I finish 4º in Final A, in the Nationals Cup of Champions, this weekend with a pretty similar components, E4 (with chassis and top deck from RS), Nosram 4.0, Nosram Istc, and Vtec 4600.
Only 2 TM E4, and the 2 cars in Final A, 4º and 7º, very good performance. Greetings, Luis C. |
Originally Posted by nocif13
(Post 4256253)
Can be put or adapt alum Bulkhead left and right and alum upper deck mount of the e4 rs on e4? So that you can install brushless motors without needing to modify cells
thank olivier ps: Congratulations, Gansei |
HI
luic you have a PM |
Originally Posted by nocif13
(Post 4269768)
???Can be put or adapt alum Bulkhead left and right and alum upper deck mount of the e4 rs on e4? So that you can install brushless motors without needing to modify cells
thank olivier ps: Congratulations, Gansei The motor mount plate, is the same, but is lightened. And the left support for center axle is the same. Greetings, Luis C. |
Originally Posted by luic
(Post 4269864)
Olivier,only one piece are different, the upper deck mount, is not in alu, is in plastic with a piece a carbon fibre for mount a tensioner.
The motor mount plate, is the same, but is lightened. And the left support for center axle is the same. Greetings, Luis C. |
Originally Posted by Canuck
(Post 4269464)
Just ordered me a 503002-C1 - 1/10 E4FS/C1 Rubber Tire Spec Electric Touring Car. It's the E4FS Rubber Conversion with (convertable) front 1 way option.
I plan on running it on a large outdoor asphalt track. http://www.rcpikeriver.com/images/rcprtrackviewbig.gif Also will have the following setup on the car: - Mamba Max with 7700 BL motor (equivalent to 7T) - Orion 4800 Lipo - 110T spur 64 pitch - Internal ratio is 2.0588 - Tires are Jaco greens (Rubberz) My question is what size of pinion should I be using ? Any suggestion on color springs to use ? I ordered the G4 spring set. Also running with a Mazda 6 Blitz body. Look forward to some help here :) about a 24t pinion (for a 9.43FDR) but i would get an assortment of spurs and pinions its alot easier to find the ratios that you need with the minimum space to move the motor. I would start with about 19lbs in the front and 17 lbs rear depending on the grip. I have a few set ups that work very well a few pages back:) |
Thanks Marcos,J .
Sent you a PM. |
Originally Posted by Canuck
(Post 4270396)
Thanks Marcos,J .
Sent you a PM. |
OK guys here is the set-up I built for my E4 this weekend, its not perfect but its a whole lot better then what I started with. I set the track record this weekend and ran away from a JRXS. Anyway here it is.
|
What version of the E4 Do you use marcos?
|
Originally Posted by Hoggy
(Post 4271810)
What version of the E4 Do you use marcos?
I'm sending your tray ASAP!!! Check your PM |
Originally Posted by Hoggy
(Post 4271810)
What version of the E4 Do you use marcos?
|
| All times are GMT -7. It is currently 03:04 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.