Tamiya mini cooper
#6362
#6363
Tech Addict
iTrader: (10)
#6364
hey new to the mini game finding a lot of valuable info so far. already got the trans bearings on the way and got some rs4 oil shocks retro fitted and going to get some universals the end of the month. The issues i am having right now is finding online hobby stores besides tower that have a m03 section for replacement parts/hop ups/bodies anybody have suggestions?
#6365
Tech Adept
Could be, but then again, I was using mine indoors, and with it located in the chassis (so not getting a lt of airflow).
Running it with a 27t Monster, XXX Brushed, Red/green springs, on 20 and 18t pinions, depending on track. Still works fine
But, thats a moot point now, as the TEU-101BK is sitting in my TA03FS, as the mini is awaiting it's exige brushless
Cheers
Ed
Running it with a 27t Monster, XXX Brushed, Red/green springs, on 20 and 18t pinions, depending on track. Still works fine
But, thats a moot point now, as the TEU-101BK is sitting in my TA03FS, as the mini is awaiting it's exige brushless
Cheers
Ed
When I installed my Exige system in my M03 I ran into a few problems. First the engine screws are too long. If you screw them in all the way the motor doesn't spin. To fix this I ran about 5mm shock spacer on the screws.
The other item and I am hoping someone can help me here. When I hooked the system up it ran in reverse. Should I switch the polarity and run the positive to the negative??? What is the fix?
#6366
When I installed my Exige system in my M03 I ran into a few problems. First the engine screws are too long. If you screw them in all the way the motor doesn't spin. To fix this I ran about 5mm shock spacer on the screws.
The other item and I am hoping someone can help me here. When I hooked the system up it ran in reverse. Should I switch the polarity and run the positive to the negative??? What is the fix?
The other item and I am hoping someone can help me here. When I hooked the system up it ran in reverse. Should I switch the polarity and run the positive to the negative??? What is the fix?
Right now u prob have faster reverse than forward.
After switching cables will be fine.
#6367
Tech Elite
hey new to the mini game finding a lot of valuable info so far. already got the trans bearings on the way and got some rs4 oil shocks retro fitted and going to get some universals the end of the month. The issues i am having right now is finding online hobby stores besides tower that have a m03 section for replacement parts/hop ups/bodies anybody have suggestions?
#6371
I know its nothing highly important but i finished putting a set of nitro RS4 2 shocks on the mini last night. They fit perfectly on the car and just looking at pictures look very similar to the mini CVA shocks
#6372
#6374
HELP!!! Exige beeps continuously
I just installed SP Exige, the motor beeps continuously and it does throttle or reverse. I bought SP 11.5R, and it is still the same. If my new Exige toast? The manual doesn't say anything about continuous beeps.
Please help, I'm running nuts.
Please help, I'm running nuts.
#6375
Tech Initiate
Exige - Continuous Beeps
Re-programmed Exige using DNA seup unit (Thanks Calvin!) however, this did not fix problem.
Finally fixed problem by selecting another 'model' on my radio (an unused one) This forced radio to default settings. Turned on Radio, full throttle, turned on Exige...beep once or twice, released throttle...then throttle again, motor spun Ok, all seems ok now...and no more continous beeps!
I think that perhaps EPA's and all settings must be set back to default or maximum etc....in any case, this worked for me...hope it helps.
Cheers,
Carl