Serpent to 1/10th EP Touring Kit S400
#3243
todb...
MIP complete axle/bone for Yok BD. Only on rear. Running the lipo tray so I can run the batt further forward for better balance and 5600's dont fit under the top deck. Also have the drive train flipped so weight can go down the centre line.
MIP complete axle/bone for Yok BD. Only on rear. Running the lipo tray so I can run the batt further forward for better balance and 5600's dont fit under the top deck. Also have the drive train flipped so weight can go down the centre line.
#3246
S400 MORE STUFF
I've been trying more mods on the S400 to keep the enthusiasm up before the S401 becomes available. Below are are few pics with ideas implemented.
Enjoy.
Second S400 gear diff installed on front with machined 2mm alloy shims to centre in bulkheads.
Front rear toe/suspension block now mounted flat for better strength with more than adequate clearance for belt with tentioner mounted just behind steering belt crank instead on top deck. This allows belt to run high enough to clear hinge pin mount. Even if roll centre shims are used.
Picture of belt tentioner now mounted just behind steering crank.
This shows amount clearance of belt.
Antenna also is now mounted on chassis instead on top deck as well i have fitted a EXOTEK LiPo brace to keep the LiPo position secure along the chassis line of the car.
You can tell i have too much time on my hands !!
Cheers
Ren
Enjoy.
Second S400 gear diff installed on front with machined 2mm alloy shims to centre in bulkheads.
Front rear toe/suspension block now mounted flat for better strength with more than adequate clearance for belt with tentioner mounted just behind steering belt crank instead on top deck. This allows belt to run high enough to clear hinge pin mount. Even if roll centre shims are used.
Picture of belt tentioner now mounted just behind steering crank.
This shows amount clearance of belt.
Antenna also is now mounted on chassis instead on top deck as well i have fitted a EXOTEK LiPo brace to keep the LiPo position secure along the chassis line of the car.
You can tell i have too much time on my hands !!
Cheers
Ren
#3250
Serpent S400 for sale Roller!!
Barely used Serpent S400
ROLLER(tekin motor & lipo not included)
Indoor carpet only
serpent front aluminum c hubs and serpent aluminum rear uprights
great for spare parts!
carbon fiber chassy, shock towers, under main carbon chassy is in good shape, upper decks, cvds, bearing blocks, hingepins tie bars, front spool, 2 new rear ball diffs(1 locked)are all in good shape
$260 shipped w usps w tracking
paypal
408 771 9993
ROLLER(tekin motor & lipo not included)
Indoor carpet only
serpent front aluminum c hubs and serpent aluminum rear uprights
great for spare parts!
carbon fiber chassy, shock towers, under main carbon chassy is in good shape, upper decks, cvds, bearing blocks, hingepins tie bars, front spool, 2 new rear ball diffs(1 locked)are all in good shape
$260 shipped w usps w tracking
paypal
408 771 9993
Last edited by ericbeenorcal; 08-23-2010 at 09:19 PM.
#3254
Tech Rookie
hello:
I have an S4000 with top cover he was wearing exotech.before
Serpent differential.
He was wearing belt pulley 16T 177T serpent.
I purchased differential spec-r Tamiya 37T.
I could say that combination of pulley and belt mounted for me worth q
These front and rear differentials.
Straps do not fall as is normal to have more teeth diferentials
a greeting and thank you very much
sorry for my English by google
I have an S4000 with top cover he was wearing exotech.before
Serpent differential.
He was wearing belt pulley 16T 177T serpent.
I purchased differential spec-r Tamiya 37T.
I could say that combination of pulley and belt mounted for me worth q
These front and rear differentials.
Straps do not fall as is normal to have more teeth diferentials
a greeting and thank you very much
sorry for my English by google
#3255
Tech Master
iTrader: (68)
Gentleman, I need some help. I found a TC race in albuqure(sp), new mexico in late feb that I want to attend. Needless to say I have not touched my s400's in a long time. Parts are not a problem for me as some of you know. What I need is setup help for 13.5 rubber touring car class using all tekin equipment and Jaco Blues as handout tires. Also 4 hole spur gears that I can mount without wobble. Thanks for all the help in advance. Also which body for this class? I have Gear diff's and spool as well. Please be in depth your advice. thanks