T.O.P. Racing "Scythe" 1/10 EP Touring Car
#1021
Tech Master
I changed from all allu options back to plastic. The Bulk head cover is stayed allu.
I have tried it last Saturday and Sunday when it was hot. I was using old tiers.
The car was reacting very well.
Yesterday I drove in the wet and the car was still stable and forgiving.
Normally I’m al over the place in the rain.
This Sunday we have our second club race. It will be hard to get in the top 10 but I think it’s possible with this car.
I’m learning the car better and better. I found out that I can’t use my Xray setups on the car. But after some help and some setups from Jan van Steeg I managed to get a good setup.
The only thing that I must check now is my cars weight. It was in all allu hop ups 1460gr. Now I think it will be close to the 1400gr and that is the minimum.
I have tried it last Saturday and Sunday when it was hot. I was using old tiers.
The car was reacting very well.
Yesterday I drove in the wet and the car was still stable and forgiving.
Normally I’m al over the place in the rain.
This Sunday we have our second club race. It will be hard to get in the top 10 but I think it’s possible with this car.
I’m learning the car better and better. I found out that I can’t use my Xray setups on the car. But after some help and some setups from Jan van Steeg I managed to get a good setup.
The only thing that I must check now is my cars weight. It was in all allu hop ups 1460gr. Now I think it will be close to the 1400gr and that is the minimum.
#1022
Tech Champion
iTrader: (1)
I changed from all allu options back to plastic. The Bulk head cover is stayed allu.
I have tried it last Saturday and Sunday when it was hot. I was using old tiers.
The car was reacting very well.
Yesterday I drove in the wet and the car was still stable and forgiving.
Normally I’m al over the place in the rain.
This Sunday we have our second club race. It will be hard to get in the top 10 but I think it’s possible with this car.
I’m learning the car better and better. I found out that I can’t use my Xray setups on the car. But after some help and some setups from Jan van Steeg I managed to get a good setup.
The only thing that I must check now is my cars weight. It was in all allu hop ups 1460gr. Now I think it will be close to the 1400gr and that is the minimum.
I have tried it last Saturday and Sunday when it was hot. I was using old tiers.
The car was reacting very well.
Yesterday I drove in the wet and the car was still stable and forgiving.
Normally I’m al over the place in the rain.
This Sunday we have our second club race. It will be hard to get in the top 10 but I think it’s possible with this car.
I’m learning the car better and better. I found out that I can’t use my Xray setups on the car. But after some help and some setups from Jan van Steeg I managed to get a good setup.
The only thing that I must check now is my cars weight. It was in all allu hop ups 1460gr. Now I think it will be close to the 1400gr and that is the minimum.
and since then I have added the hard arms to improve it further and run slightly lighter oil in the rear shocks to retain the driveability. Also I have removed the ackerman plate and run the bellcrank in the forward position to improve high speed steering and to provide more consistent balance from high to low speed turn in.
#1023
Tech Master
Rather interesting reading... I used to run my scythe full plastic. It had no idea of the meaning of "loose" back then and was quick. But I decided to go the carpet flex chassis so the diffs are easier to get to. The car has lost some of its driveability for sure.. but you can remove the two screws on top of the motor bulkhead and it is just as good. The stiffer version has much more mid corner speed...
and since then I have added the hard arms to improve it further and run slightly lighter oil in the rear shocks to retain the driveability. Also I have removed the ackerman plate and run the bellcrank in the forward position to improve high speed steering and to provide more consistent balance from high to low speed turn in.
and since then I have added the hard arms to improve it further and run slightly lighter oil in the rear shocks to retain the driveability. Also I have removed the ackerman plate and run the bellcrank in the forward position to improve high speed steering and to provide more consistent balance from high to low speed turn in.
Do you run on carped or tarmac?
I run on tarmac.
I have the ackerman plate placed back so the car reacts faster.
I can send you my setup.
I had also placed my ackerman in the frond. also the steering servo i placed to the frond. I had it ful allu.
I didn't had anny problems with a loose back.
I had to manny grip in the back when i was running full plastic.
Now i changed my rolcenter at the back. I use the yellow springs from xray arround.
I want to buy a second car and also the carpet flex chassis.
Can i put an other topdek and chassis plate under it?
Because i want to use it for rubber indoor. else i keep it with the allu set that i already have.
I think that i buy an extra ackerman plate. There i wil dril an extra hole in so my ackerman comes more to the front on the plate.
Than i have more steer and a better reaction on the steering. (I hope)
Greetings Emiel
#1026
Tech Fanatic
congrats to kyle berkstrom, e.j. evans and kevin jelich for your stellar performances at the reedy race
#1029
Tech Champion
iTrader: (1)
Do you run on carped or tarmac?
I run on tarmac.
I have the ackerman plate placed back so the car reacts faster.
I can send you my setup.
I had also placed my ackerman in the frond. also the steering servo i placed to the frond. I had it ful allu.
I didn't had anny problems with a loose back.
I had to manny grip in the back when i was running full plastic.
Now i changed my rolcenter at the back. I use the yellow springs from xray arround.
I want to buy a second car and also the carpet flex chassis.
Can i put an other topdek and chassis plate under it?
Because i want to use it for rubber indoor. else i keep it with the allu set that i already have.
I think that i buy an extra ackerman plate. There i wil dril an extra hole in so my ackerman comes more to the front on the plate.
Than i have more steer and a better reaction on the steering. (I hope)
Greetings Emiel
I run on tarmac.
I have the ackerman plate placed back so the car reacts faster.
I can send you my setup.
I had also placed my ackerman in the frond. also the steering servo i placed to the frond. I had it ful allu.
I didn't had anny problems with a loose back.
I had to manny grip in the back when i was running full plastic.
Now i changed my rolcenter at the back. I use the yellow springs from xray arround.
I want to buy a second car and also the carpet flex chassis.
Can i put an other topdek and chassis plate under it?
Because i want to use it for rubber indoor. else i keep it with the allu set that i already have.
I think that i buy an extra ackerman plate. There i wil dril an extra hole in so my ackerman comes more to the front on the plate.
Than i have more steer and a better reaction on the steering. (I hope)
Greetings Emiel
I recommend the carpet flex just for the ease of diff access. It is similar to full alloy version when you don't use the posts.
Don't worry bout ackerman plate, just use the forward hole on the deck for the bellcrank. Saves a bit of weight.
#1030
Is there somewhere on line I can buy it?
#1031
Tech Champion
iTrader: (1)
#1032
Tech Champion
iTrader: (3)
Join Date: Mar 2003
Location: Peoples Republic of Northern Virginia
Posts: 5,682
Trader Rating: 3 (100%+)
http://www.muchmoreracing.com/news/n...uring-car.html
The link for the USA/Canada distributor http://www.teammuchmore.com/ does not have any content.....
Ampdraw has it listed but out of stock
http://www.ampdraw.com/product.php?a...productid=3228
The link for the USA/Canada distributor http://www.teammuchmore.com/ does not have any content.....
Ampdraw has it listed but out of stock
http://www.ampdraw.com/product.php?a...productid=3228
#1033
Tech Elite
iTrader: (27)
#1034
OK guys, sorry for all the mystery, but TOP Racing USA is the sole distributor for T.O.P. Racing Products in North America. Your local hobby shop can order from us or if they are not willing we will sell directly to you. Contact us at [email protected]
#1035
Tech Master
What is the difrence between the 2006 version and the 2008 version except the alu bulkheads and the v2 drive shafts?
I want to buy a seccond one.
I want to buy a seccond one.