XRAY XB9E Official Thread - they did it :)
#361
any idea on when that is?
#362
Tech Regular
iTrader: (4)
http://www.teamxray.com/teamxray/new...d2587ebefd34b2
The springs are a few posts down.
#364
Tech Master
iTrader: (77)
http://forum.teamxray.com/viewtopic....13589&start=20
I already picked one of these up and it's at my painters shop already :-)
Last edited by Wease; 07-28-2013 at 01:32 PM.
#365
Tech Champion
Thread Starter
A few pages back the Euro guys said the JConcepts XB9 Finnisher body is a great fit. And here is the confirmation on the XRay Forums:
http://forum.teamxray.com/viewtopic....13589&start=20
I already picked one of these up and it's at my painters shop already :-)
http://forum.teamxray.com/viewtopic....13589&start=20
I already picked one of these up and it's at my painters shop already :-)
Many drivers complained about the lack of a specific XB9E body even on Xray forum but nobody there seems to care about it at all. A good thing for Xray is that the XB9 is a great basis but I don't like the lack of feedback and bad communication of the brand. When you compare it to Tekno, JQ and other teams it's a night and day difference
#366
Just pre ordered mine! and tips on what else to buy with the kit?
#367
Tech Champion
Thread Starter
awesome!
I only broke a rod end on my 808 so I don't want to spend too many $$$ in replacement parts this time. Xray buggies are very strong so I'll wait to break something to order the part needed
I went with these parts, just because local tracks are rough and we race under any conditions:
- DERacing skidplates + mudgards
- m2c front shock tower protection
I only broke a rod end on my 808 so I don't want to spend too many $$$ in replacement parts this time. Xray buggies are very strong so I'll wait to break something to order the part needed
I went with these parts, just because local tracks are rough and we race under any conditions:
- DERacing skidplates + mudgards
- m2c front shock tower protection
#368
awesome!
I only broke a rod end on my 808 so I don't want to spend to many $$$ in replacement parts this time. Xray buggies are very strong so I'll wait to break something to order the part needed
I went with, just because local tracks are rough and we race under any conditions:
- DERacing skidplates + mudgards
- m2c front shock tower protection
I only broke a rod end on my 808 so I don't want to spend to many $$$ in replacement parts this time. Xray buggies are very strong so I'll wait to break something to order the part needed
I went with, just because local tracks are rough and we race under any conditions:
- DERacing skidplates + mudgards
- m2c front shock tower protection
#369
Tech Champion
Thread Starter
http://www.deracing.net/store/index....ry&path=99_177
#370
yes it should fit based on the Deracing website:
http://www.deracing.net/store/index....ry&path=99_177
http://www.deracing.net/store/index....ry&path=99_177
would the shock bras really do much?
#371
The M2C shock bra works like a champ, but always use ca glue to seal your carbon edges also.
#372
#373
Tech Champion
Thread Starter
@EGA0007: the car is mounted apart from the servo saver and electronics that I will have to remove from another buggy. I ordered the finnisher body too so it should arrive at the end of the week. In Belgium there is no shop with these parts in stock, I have to order the parts on amainhobbies . It's much cheaper even coming from the US too, the shipping costs on amain are 0,60$
As I said earlier I want to take my time for this one, it's my very first new 1/8 buggy. I have to prepare the JQ for a race this week end and the Durango for an endurance the week end after so I'm quite busy
#374
Tech Initiate
Well i've ordered the XB9e also and offcourse i order the JConcepts Illuzion Finisher body. The shock tower bra is sold out at A Main, so looking for somewhere else (since i'm dutch i have to watch the shipping costs). The finish it off i'm looking for the Tekin RX8 Gen2 and Tekin T8, 1900kv motor (if possible Gen2).
I don't need spare parts, since we have a supplier at the track (and he's living a few hundred meters away from me)... My luck and also a reason to switch to XRAY
I don't need spare parts, since we have a supplier at the track (and he's living a few hundred meters away from me)... My luck and also a reason to switch to XRAY
#375
Tech Champion
Thread Starter
Well i've ordered the XB9e also and offcourse i order the JConcepts Illuzion Finisher body. The shock tower bra is sold out at A Main, so looking for somewhere else (since i'm dutch i have to watch the shipping costs). The finish it off i'm looking for the Tekin RX8 Gen2 and Tekin T8, 1900kv motor (if possible Gen2).
I don't need spare parts, since we have a supplier at the track (and he's living a few hundred meters away from me)... My luck and also a reason to switch to XRAY
I don't need spare parts, since we have a supplier at the track (and he's living a few hundred meters away from me)... My luck and also a reason to switch to XRAY
excellent choice for the tekin combo