1/8 buggy body fit guide
lets start a guide of what 1/8 bodies will work on different chassis.
I think about this a lot and I think it would help out a lot of people if we were to collectivly pool information. width is usually the biggest factor. most everything else can be trimmed to work ill start with the few I know. Body dimensions: hot bodies Ve8 body is 5 1/2" wide losi 8ight-E body is 7 3/4" at the front 5 1/2" wide at the rear but can be stretched a bit chassis dimensions: hot bodies ve8 chassis is 5 1/2" wode hot bodies D8 chassis is 7 3/4" wide Compatability: losi 8ight bodies will fit all tekno V4 chassis FTW tekno v4 body will fit a hot bodies Ve8 with a bit of velcro a few specific ones I am looking for are widths of the associated RC8Be and kyosho MP9e post em up! |
good thread :)
FTW Exabyte for a MBX6 tekno v4 fits on a converted DNX408 too with few mods |
The bulldog for the rc8.2e fit on my old Ofna Lx2e. It needs a bit of trimming though :)
|
anyone have dimensions of the durango buggy bodies?
|
looking for body widths of the following
Xray 808E Kyosho MP9E Associated RC8Be Mugen mbx6 can owners measure your body shells please? |
Just got a new proline bulldog for rc8.2e I think it is right at 7 3/4 at its widest point. I am actually using it on a older Xray XB8-EC that I converted to brushless. Fits perfect, onlly difference is the front area needs to be left a little long because the xrays front mount real close to the front tower.
|
The bullydog nitro rc8.2 fits the rc8be. It doesn't have much clearance for the batteries though.
|
Rc8.2 Bulldog fits all Caster Buggys and RC8T Bodies fits the Caster Truggy, you have to trim side guards down a tad if you want to keep them on.
FTW MBX6 body will fit Caster EX 1.5 with some custom trimming and trimmed down side guards. |
Losi 8ight-E Stock body will fit a Tekno V4 VE8 with Velcro, of course.
|
TEKNO V4 D8 BODIES:
JCI0072 - JConcepts Losi 8ight-E 2.0 Illuzion Body PRO331540 - Pro-Line Slipstream Losi 8ight-E 2.0 LOSA8097 - Team Losi 8ight-E FTW00027A - FTW R/C Tekno RC V4 D8 Exabyte HPI VORZA BODIES: KYOIFB002 - Kyosho MP-9 Body JJCI0077 - Concepts - Illuzion Kyosho MP9 Hi-Flow PRO3295-40 - Pro-Line - Shift Kyosho MP9 HBS67444 - Hot Bodies - D8 Body JCO0075 - JConcepts - Illuzion Hot Bodies D8 Hi Flow 3370-00 - Pro-Line - 2012 BullDog Hot Bodies D8 3327-00 Pro-Line Bulldog Hot Bodies D8 *All these bodies may require mods and/or velcro |
I was told in the Mp9 thread that the Rc8.2e body will fit the kyosho with roomfor batts. Just need to leave the nose on like you would the kyosho and trim to fit. If geta chance I will measure my Tki2
|
I have a jammin x1cr that I am converting to brushless. I've read that the body will not fit over the batteries once the conversion is complete. If this is true what body could I use?
|
Team associated RC8B bodies will fit the hot bodies D8 with little to no modifications. Im running one using only velcro, instead of the body posts.
|
Anything for the Mugen Eco?
|
I know a guy that runs a losi 8ight body on a mugen mbx6.
|
All times are GMT -7. It is currently 07:06 AM. |
Powered By: vBulletin v3.9.3.8
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.