nexxus

iTrader: (315)

Icharger 406 Duo, purchased prior to 2017 States and was my main charger for a good few years, Always well looked after and reliable however recently channel 1 has been intermittant about wanting to charge packs, Channel 2 still works flawlessly (as was seldom used) and Channel 1 still seems fine as the discharge side.
Used that as an excuse to upgrade to a DX8 but this would still suit someone chasing an Icharger but can't afford the $600 new price for one of these. Has lived on my bench the past year as a home charger and never skipped a beat but as we seldom RC anymore outside of running TC I can't rationalise keeping it.
Will come with basic charge leads
iCharger 406 Duo Specifications:
Input Voltage:
10-30 Volts
Max Input Current: <60 Amp, CH1/2<47A
DC Charge Current Range: 70A@Syn. Mode - 40A@Asyn. Mode
Maximum Charge Power Capacity: 1400W (Channel 1000W @input > 23.5V)
Maximum Discharge Power Capacity: 140W (Channel 80W)
Maximum Regenerative Discharge Capacity: 1400W (Channel 1000W)
Current Drain for Balancing: 2.4A@Syn. Mode 1.2A@Asyn. Mode
Balance Accuracy: <10mv
Lithium (LiPo/Lilo/Life) battery cell count: 1-6 series (Per Channel)
NiMh/NiCd Battery Cell Count: 1-25 Series (Per Channel)
Pb (Lead Acid) Cell Count: 1-18 series 2-30v (Per Channel)
Battery Setup Memories: 64
Intelligent Temperature Control: Yes
PC Connect: USB Port
Weight: 0.91 Kg
Dimensions (LxWxD: 171x118x59
iCharger 406 Duo Features:
The 406DUO uses advanced Synchronous buck-boost DC/DC converter technology, high power, a high current and high-performance power conversion circuit. The maximum charge power capacity is up to 1400W, the maximum charge/discharge current of a channel is up to 40A, and two channels in Synchronous Mode are up to 70A.
Each channel supports 6s LiPo, Lilo, LiFe and NiZn batteries, with maximum 1.2A balance current, and adopts a unique balance calculation of internal resistance correction. Supports 1-20s NiMH/NiCd batteries and 1-12s Pb batteries.
With 1A/5V USB charging port, convenient for the user to charge mobile phones and PCs.
When the channel output connects the battery after the charger powers on, it will start automatically the anti-sparking protection.
Intelligent fan control. Sensing internal temperature via the internal temperature sensor, to thereby control the fan speed.
Internal temperature protection. When the internal temperature exceeds the Power Reduce temperature, the output power is automatically reduced; and the charger will shut down when temperature exceeds the Shut-down temperature.
This charger can save 64 parameters sets and support the data import/export to SD card.
A 2.8-inch LCD screen provides rich information including current, voltage, power, capacity, internal resistance, control status, time-consuming and temperature, etc.
Multi-discharge features: self-discharge, regenerative to input discharge, and lithium battery extra expanding discharge.
Supports measurement for internal resistance of battery offline and online. Can measure not only the internal resistance of the entire battery pack, but also measure the internal resistance of each cell within the lithium battery.
The iCharger has protection for reversed polarity (input or output), input voltage/current, battery temperature, charging capacity, overrun time and maximum power etc.
Supports upgrading the hardware program by USB port or SD card. The iCharger also supports the “Logview” software and can display, plot and analyze the charge and discharge data by it. (See detailed information about Logview at the following website: http://www.logview.info)

$170 shipped

nexxus

iTrader: (315)

Up

nexxus

iTrader: (315)

Up