The Hill Camp Courtney RC Park Okinawa Japan
#136
Jason, you still awake? Call me at 090 6857 2843, got a ? on the DB-01 and need your help. Thanks
#137
Tech Adept
iTrader: (2)
I have been holding off passing this info until I tried these batteries. I have several runs on the first set , liked them so much I bought another. They power the MMM without issue and will fit anything a standard 6cell stick fits. I have not tried shipping to my new address so I went to APO and they still got here in about two weeks. About one week if you ship to your downtown address.
http://cgi.ebay.com/RC-Lab-5000mAh-3...item2a041094d2
http://cgi.ebay.com/RC-Lab-5000mAh-3...item2a041094d2
#138
Battery fits fine in the DB-01 the holddown pins will have to be backed out some.......doesn't fit the DF-03.
Jason did you have any clearance issues with the steering linkage from the servo?
Jason did you have any clearance issues with the steering linkage from the servo?
#140
Tech Addict
Ken,
Sounds like you may be nearing the end of your DB01 build. Quick tip...trim your rear wing so it does not touch the rear shock tower, or make the mounting holes in the rear wing a little closer towards the leading edge so when you mount it up it'll sit farther back and not touch the rear tower.
I've read that the DB01's have an issue with breaking rear towers, and the cause has been tracked down to the rear wing putting a load on it since it rests directly on it.
I trimmed mine so it doesn't touch and never had a problem, never broke a tower.
- Paulie
Sounds like you may be nearing the end of your DB01 build. Quick tip...trim your rear wing so it does not touch the rear shock tower, or make the mounting holes in the rear wing a little closer towards the leading edge so when you mount it up it'll sit farther back and not touch the rear tower.
I've read that the DB01's have an issue with breaking rear towers, and the cause has been tracked down to the rear wing putting a load on it since it rests directly on it.
I trimmed mine so it doesn't touch and never had a problem, never broke a tower.
- Paulie
#141
Tech Initiate
Hey Gents. Have a good time with the track. I'll be with Josh, and will be back in April. Hopefully we can walk into a nice race schedule! Take care guys, and have fun.
Brian
Brian
#142
Brian, good luck and have a safe trip. Thanks for your service!!
#143
Tech Addict
Brian, keep your head down and stay safe. We'll see ya when you get back.
- Paulie
- Paulie
#144
sure could use a couple of days of this drizzling rain.
#145
Anybody go by the track, did the rain yesterday make a difference?
#146
Guess no one's got anything to say...
Think most of us had a good time on Sunday for a few hours. The guys from Schwab came down again and another guy with a truggy showed up, his dedicated wife with the fuel bottle...
who was the guy with the camera taking pics? need to get some of those...
See a lot of monster trucks coming out...may have to break out the E zilla and kick some nitro butt...
couple a notes:
be considerate when others are present...
Think most of us had a good time on Sunday for a few hours. The guys from Schwab came down again and another guy with a truggy showed up, his dedicated wife with the fuel bottle...
who was the guy with the camera taking pics? need to get some of those...
See a lot of monster trucks coming out...may have to break out the E zilla and kick some nitro butt...
couple a notes:
be considerate when others are present...
- drive ONLY on the track, not around other tracks or near parking area
- drive from in between the 1/8 and 1/10 track, don't drive from the middle of the track
- CHECK YOUR FREQUENCY BEFORE STARTING YOUR CAR!!!
- If you stop your car on the track try to make sure it's not in the way of other cars driving
#148
Anymore thoughts on Saturday, I swapped days with the wife and I plan to be at the track on Saturday...... hope the buggy gets back together in time.
Last edited by bando711; 01-26-2010 at 04:34 PM.
#149
Robert, do we have an update on the stand, if we are looking at dates in Feb. for an event, we need time to prepare and adjust the track if needed after the stand is in palce.
#150
Tech Addict