475LikesInspire us. Show me your BEST, CLEANEST electronics installation pics.
10-27-2009, 02:14 AM
#677
sc10 brushless and rx install
I need to add the steer servo and do a final clean up.I used aircraft tie string the stuff they use on the apache helicopters and military planes to tie the wires up for a zip tie free
no sharp stuffclean install
I will post up the final draft soon.
no sharp stuffclean install I will post up the final draft soon.
10-27-2009, 03:27 AM
#678
Tech Apprentice
Hello, this is my little contribution:
10-29-2009, 01:54 PM
#680
Tech Regular
Finished tidying up my T2 009, dropped quite a bit of weight with all the extra cable I had.
11-03-2009, 05:41 PM
#681
Didn't have black wire, so used the original Tekin 12ga. stuff that comes with the rs. This was tricky mostly because the fan, servo, esc, and transponder are all oringal length wire. It was hard hiding it all, but turned out half decent.
Took with my phone, sorry for quality. enjoy.
Took with my phone, sorry for quality. enjoy.
11-07-2009, 04:31 AM
#682
Tech Apprentice
This turned out to be a quick job as it was required to hit the track the next day. Will probably go over it again when time allows it to happen! Figured I'd share anyway though
11-10-2009, 07:43 PM
#684
Well I think my car is finally done. Went from a nomadio radio to a 4PK. KO full size servo to a Futaba 9551, car anodized black, got rid of everything purple on the car. They dont make a sensor wire short enough for this car LOL, thats a 70mm TQ wire and I still have to roll it up inbetween the motor and esc. But other then that im happy, and can actually say that the servo, RX, and PT have real black wire
Hitec makes it, and its dialed!
I dont have a fancy light box or anything, so on my pit mat will have to work. Aha
Hitec makes it, and its dialed!I dont have a fancy light box or anything, so on my pit mat will have to work. Aha
11-10-2009, 08:15 PM
#685
Im have been working on the exact same wiring layout on my xray as you have there. 
Looks really clean. Did you cut the back of the case to allow the wire to come out the back of the speedo?
Looks really clean. Did you cut the back of the case to allow the wire to come out the back of the speedo?
11-10-2009, 08:18 PM
#686
Haha right on! Thanks
Yeah, had to cut the back of the case.
Forgot to say to, thats a no antenna FASST rx. Helps clean up everything
Yeah, had to cut the back of the case.
Forgot to say to, thats a no antenna FASST rx. Helps clean up everything
11-10-2009, 08:22 PM
#687
Yeah I did the same thing to mine. Looks good.
11-21-2009, 08:48 AM
#688
Well I think my car is finally done. Went from a nomadio radio to a 4PK. KO full size servo to a Futaba 9551, car anodized black, got rid of everything purple on the car. They dont make a sensor wire short enough for this car LOL, thats a 70mm TQ wire and I still have to roll it up inbetween the motor and esc. But other then that im happy, and can actually say that the servo, RX, and PT have real black wire Hitec makes it, and its dialed!
I dont have a fancy light box or anything, so on my pit mat will have to work. Aha
Hitec makes it, and its dialed!I dont have a fancy light box or anything, so on my pit mat will have to work. Aha
I just finished my XRAY T3 last night and snapped some pics. TO me it looks similar to my 009 except I am now using a 4PK and had to adjust the wires to the batteries as they needed to be lengthened.
Off to race!
Last edited by IIGQ4U; 11-21-2009 at 10:14 PM.
