475LikesInspire us. Show me your BEST, CLEANEST electronics installation pics.
02-20-2009, 07:19 AM
#241
Tech Master
Here's a couple of pics of my 12th car. I am still using a brushed setup, which makes the wiring job easy, although you'll notice on one of the pics that I made an upper pod plate and cross brace that uses only 1 damper tube. That makes the motor wires a little bit more tricky to look neat as you have to wire them between the end of the cells and under the cross brace. I will get a brushless setup at some point but no need to at the moment as my car goes fine as it is! All the best guys, Chris. 
02-20-2009, 08:38 PM
#242
Wow thats very nice. You have so much space to play with tho. The electrics on mine are neet but are very close together. What reciever is that ? I have a novak 13.5 and the sensor lead snapped at the speedo end. SOO i had to cut the sensor wire and solder another bit of sensor lead to it. It was very time consuming but i did it. And i shortened it at the same time. Just gets rid of some of that unwanted sensor lead.
02-23-2009, 07:51 AM
#243
02-23-2009, 08:43 AM
#244
02-23-2009, 11:47 AM
#245
My wiring.
Here is the pic i posted of my cyclone on the previous page. 
I have made a few adjustments to my electronics instalation since then. I have moved my ESC closer to the motor which gives me room to put my reciever down on its bottom and i have have shortened my ESC and servo leads. I have also polished up my Novak motor. And put on a black antenna
. A good tip for an old looking novak motor. I polished it up with T-Cut which is a car scratch remover type polish and it came up like chrome. I just need a low profile servo now so i can mount my pt and switch to the side of that, Heres the new install.
Find more pics of my old install on previous page and compare them !
I want to know which instalation looks neater to you guys ?
I have made a few adjustments to my electronics instalation since then. I have moved my ESC closer to the motor which gives me room to put my reciever down on its bottom and i have have shortened my ESC and servo leads. I have also polished up my Novak motor. And put on a black antenna
. A good tip for an old looking novak motor. I polished it up with T-Cut which is a car scratch remover type polish and it came up like chrome. I just need a low profile servo now so i can mount my pt and switch to the side of that, Heres the new install. Find more pics of my old install on previous page and compare them !
I want to know which instalation looks neater to you guys ?
02-23-2009, 12:24 PM
#247
thanks
thanks mate !
if you have any questions on how ive done things that your not sure of let me know on here or pm me.
if you have any questions on how ive done things that your not sure of let me know on here or pm me.
02-23-2009, 01:12 PM
#248
That looks like an LRP speedo .. but its red... someone care to tell me wtf sup witk that ? 
02-23-2009, 01:26 PM
#249
02-24-2009, 06:32 AM
#250
esc
yes the pic of the esc is a nosram one. I am in the UK so the nosram ones ar e popular here although alot have the lrp one. RED IS BETTER lol
02-24-2009, 06:51 AM
#251
02-24-2009, 07:59 AM
#252
Pretty simple really .. Its called heat shrink. And a deans just looks like a toy connector. The Barrels have more surface area and no plastic.... other than the heat shrink.
02-25-2009, 01:43 AM
#253
I'll play
My Mini
My Mini
Last edited by alphaqgti; 03-31-2009 at 04:19 PM.
02-25-2009, 01:53 AM
#254
