Hpi Pro 4
Tech Regular
hi
can someone with a pro 4 please measure the length of the centre shaft ( pin to pin) and the widths of the pin.
hope thats clear enough,
thanks
A Gower
can someone with a pro 4 please measure the length of the centre shaft ( pin to pin) and the widths of the pin.
hope thats clear enough,
thanks
A Gower
Tech Champion
iTrader: (42)
Originally posted by pro4racer
hi
my club changes to carpet soon and i was wondering with the current gear ratio i am using now would i have to change that wen the carpet goes down.
also would i want a harder suspension on carpet or soft
thanks
hi
my club changes to carpet soon and i was wondering with the current gear ratio i am using now would i have to change that wen the carpet goes down.
also would i want a harder suspension on carpet or soft
thanks
if the track is a lot smaller just go down 3-4 teeth on the pinion to start with. if you give the dimensions of your track and if you're running rubber or foam tires some of the people on this thread might be able to give more specific feedback.
some people say that an indoor carpet setup and an outdoor asphault setup can be somewhat close.
this is all on rubber tires.....if you run foams with an entirely different setup.
Originally posted by agower
hi
can someone with a pro 4 please measure the length of the centre shaft ( pin to pin) and the widths of the pin.
hope thats clear enough,
thanks
A Gower
hi
can someone with a pro 4 please measure the length of the centre shaft ( pin to pin) and the widths of the pin.
hope thats clear enough,
thanks
A Gower
I measured that and lenght of center shaft pin to pin = 16.3cm
Width of the pin = 2.5mm
Hope that help
Tech Master
iTrader: (1)
Originally posted by RC_Mice
DHI-CUP 2005, Odense, Danmark
Is it a Atsushi Hara car ? check the link below.
http://www.e-image.dk/gallery/2005/20050115/default.asp
DHI-CUP 2005, Odense, Danmark
Is it a Atsushi Hara car ? check the link below.
http://www.e-image.dk/gallery/2005/20050115/default.asp
Tech Regular
dogbone
I remember reading somewhere on this thread that you can replace Pro4's dogbone with the stronger one from TC3 or something? but i can't find that post again even using the search function.
so is it true? and what's the part# for the TC3 dogbone ?
btw, i've already broke two dogbones in 3 months time, i'm just racing it with a silver can motor. no big crash or anything, both of the dogbones broke at the "round" bit near the wheel side if you know what i mean. it appears to me that area got worn out and become very thin by the time it was broken... is it usual? what can i do to prevent it?
so is it true? and what's the part# for the TC3 dogbone ?
btw, i've already broke two dogbones in 3 months time, i'm just racing it with a silver can motor. no big crash or anything, both of the dogbones broke at the "round" bit near the wheel side if you know what i mean. it appears to me that area got worn out and become very thin by the time it was broken... is it usual? what can i do to prevent it?
Tech Champion
iTrader: (9)
I replaced my front bones with the MIP shiny TC3 bones
#1481
#1481
Tech Regular
this one?
http://www2.towerhobbies.com/cgi-bin...?&I=LXSR37&P=7
it'll be a direct replacement? no mods needed i suppose? Thanks
http://www2.towerhobbies.com/cgi-bin...?&I=LXSR37&P=7
it'll be a direct replacement? no mods needed i suppose? Thanks
Tech Champion
iTrader: (31)
Originally posted by yellow15
this one?
http://www2.towerhobbies.com/cgi-bin...?&I=LXSR37&P=7
it'll be a direct replacement? no mods needed i suppose? Thanks
this one?
http://www2.towerhobbies.com/cgi-bin...?&I=LXSR37&P=7
it'll be a direct replacement? no mods needed i suppose? Thanks
are those ones suppose to be better?
Yellow15,
The MIP TC3 bones are crap. Try the new upgraded AE TC3 thick blue bones. They are stronger & lighter than the steel MIP's.
Cheers.
The MIP TC3 bones are crap. Try the new upgraded AE TC3 thick blue bones. They are stronger & lighter than the steel MIP's.
Cheers.
Registered User
IRS big dawg bones for the TC3 work really good. They are bigger in diameter so they're much more resistant to bending. They also have pin cushins and 2 sets of coupler pin holes when your first set wears out.
Tech Regular
Originally posted by Vance
Yellow15,
The MIP TC3 bones are crap. Try the new upgraded AE TC3 thick blue bones. They are stronger & lighter than the steel MIP's.
Cheers.
Yellow15,
The MIP TC3 bones are crap. Try the new upgraded AE TC3 thick blue bones. They are stronger & lighter than the steel MIP's.
Cheers.
Originally posted by yellow15
do you got a link to those bones? does towerhobbies have them?
do you got a link to those bones? does towerhobbies have them?
Tech Initiate
any idea when the 2005 version comes out?
Tech Addict
iTrader: (3)
Originally posted by Totalfixation
any idea when the 2005 version comes out?
any idea when the 2005 version comes out?