YOKOMO Touring Car BD-7
#305
Suspended
#306
Tech Apprentice
But another Question!!!
Iīve builded the car in a few hours, installed everything... No Problems so far... BUT! My pinions doesnīt fit, because they do not rotate in a straight line with the spur gear... About 2mm off... :-(
Has anybody the same problem? Or what pinions do you guys use?
#307
Tech Elite
iTrader: (8)
Yes! ;-)
But another Question!!!
Iīve builded the car in a few hours, installed everything... No Problems so far... BUT! My pinions doesnīt fit, because they do not rotate in a straight line with the spur gear... About 2mm off... :-(
Has anybody the same problem? Or what pinions do you guys use?
But another Question!!!
Iīve builded the car in a few hours, installed everything... No Problems so far... BUT! My pinions doesnīt fit, because they do not rotate in a straight line with the spur gear... About 2mm off... :-(
Has anybody the same problem? Or what pinions do you guys use?
I'm sure this i a huge suprise....I run Trinity/Epic pinions.
#309
Tech Apprentice
Use two small pieces of double sided tape on the front and rear of the battery then use strapping tape. It will help keep everything in place. Otherwise yes round the edge and apply ca glue.
Did you flip the pinion? or is it just wobbly? Do you have a pic?
I'm sure this i a huge suprise....I run Trinity/Epic pinions.
Did you flip the pinion? or is it just wobbly? Do you have a pic?
I'm sure this i a huge suprise....I run Trinity/Epic pinions.
Iīve tested a tamiya pinion... it works! I think the Xenon ones are to long!
So i have to find something like the tamiya pinions
#311
Tech Elite
iTrader: (8)
http://www.amainhobbies.com/advanced...29&filter_cat=
These are the spurs I have been looking at. My 72 tooth are one of these. You can only use two screws to tighten it down but I can get it in. If I run mod I will use 4 screws and the stock spur.
http://www.amainhobbies.com/product_...r-Gear-64P-88T
These are the Kyosho ones that look like they would work.
These are the spurs I have been looking at. My 72 tooth are one of these. You can only use two screws to tighten it down but I can get it in. If I run mod I will use 4 screws and the stock spur.
http://www.amainhobbies.com/product_...r-Gear-64P-88T
These are the Kyosho ones that look like they would work.
#312
Tech Regular
iTrader: (16)
That would mean with a 72 you would need around a 66 tooth pinion to have any hope of achieving a mesh (quick from the hip calculations, feel free to double check). That would give a 2.18 FDR...
Buy some RWs in the 90-96 range (I carry 93 & 96s) and you will be covered.... Preferably V2s which let you use all 4 screws.
Mike
#313
Tech Elite
iTrader: (9)
They don't seem to have 93s available.
You won't be able to achieve a functional gear ratio with that 72. With a 93 the smallest pinion I could mesh, and even this was pushing it, was a 45 for a FDR of 4.13.
That would mean with a 72 you would need around a 66 tooth pinion to have any hope of achieving a mesh (quick from the hip calculations, feel free to double check). That would give a 2.18 FDR...
Buy some RWs in the 90-96 range (I carry 93 & 96s) and you will be covered.... Preferably V2s which let you use all 4 screws.
Mike
That would mean with a 72 you would need around a 66 tooth pinion to have any hope of achieving a mesh (quick from the hip calculations, feel free to double check). That would give a 2.18 FDR...
Buy some RWs in the 90-96 range (I carry 93 & 96s) and you will be covered.... Preferably V2s which let you use all 4 screws.
Mike