wheruat

iTrader: (1)

RC-DriftNewb- hey whats up. well took it out on Sat and noticed that the cvd pin is eating the cup up and is causing the car to fell a jerky. Do you know of any other shafts i can use beside the cvd's (purple) but otherwise it feel good. I put some T-Drift on them too and drifted with some of the guys but the car felt the same jerky but otherwise felt ok. Re-geared the Avid for speed and got it up to back 50-53mph but cant seem to keep the car on the ground. lol. Gona to try to make it out to a drift comp this weekend at SpeedTech in San Gab. if i can get the parts for the car. ill keep you updated.

Syber Serulean

iTrader: (28)

my brother runs NTC3 front CV bones instead of the HPI purple aluminum ones. He kept bending the aluminum ones with the front one-way so with these ones, no more bending.

wheruat

iTrader: (1)

Syber Serulean-Thx im gonna have to go and get them bad boys. thx again

RC-DriftNewb

iTrader: (1)

Just thought I'd bump this up. Anyone still running a pro4?

Outdoor season starts in a few weeks and I'll be running my pro4 in the stock, possibly pro stock class.

Should be fun!

Pit-racer

iTrader: (4)

I'll be running mine .....

akimoto

iTrader: (11)

hi guys!
all my touring are pro 4, and i'm comfortable with ,
where im racing,this cars are decent , are not top the line but, does the job, after few years racing , i learn something, not the car is the major problem , the driver .i'm using PRO 4 for drift, vintage, stock touring, mod touring,indoor, out door, the best performance was indoor (carpet) foam tires mod touring. I have issues that's sure ,out door all my care are so lose special rear end, but still trying ...........................

all the best for all

gibletmcshannon

Hello,

I got a PRO4 on ebay and Im getting it ready for a friend. Im impressed
with it. So much so that Ill probably buy a cyclone this year for myself

I need a favour though. My friend uses stick packs at the moment
and the PRO 4 is missing some little parts I need. I have ordered the
screws `Z305` from an `edealer` and I have the keeper parts to stop the pack moving left or right.

Now I need the two battery posts part 73512 (4) to complete the
job.

Anyone on this forum feeling charitable and let me have them for
a small fee? I can paypal the money.

Regards

Nigel (UK)

Syber Serulean

iTrader: (28)

or you can just tape it down like you would have to do in the cyclone

gibletmcshannon

Yeah it could be taped down and I do on my car, but the pro 4 is not for me, its for a friend who cant be trusted to tape it down

I still need them posts...anyone ?

jimfreeman77

HI, has anyone got some HPI silver and Pink springs lying around i can buy? PM me, cheers

RC-DriftNewb

iTrader: (1)

The Pro4's still got it! Opening day at the track, TQ'd and took second in the main!

tc3 racer sc

hi i wanted to put brushless in my pro 4 but the motor will not sit right what i need to do i hve the after market purple motor mount what i need to do i hve a novak brushless system thxs reggie

RC-DriftNewb

iTrader: (1)

Uh...what? Put some punctuation in there so I can understand what you're saying.

akimoto

iTrader: (11)

u do something wrong, should fit perfect!!!!!!!!!!!!!!!

RC-DriftNewb

iTrader: (1)

The only thing you should have to do is put the screws in the correct holes. That shouldnt both be on the same side of the motor. The upper screw should sit close towards the center of the car, and the lower one, should sit towards the outer edge of the car. Then it slides right on.