The Speed Passion Thread
#5671
What settings are used? Would you want your delay so be alot latter than 13.5. I'm running at mikes-hobbyshop.com in porter Texas. This is the track where they just held the nitro worlds. Running a tc5
#5672
Tech Adept
Anyone got a good starting point set up for a SP v2 lpf in a mini m05 using a 17.t motor with standard gearing? Track is small and technical 20mx30m.
#5673
Tech Champion
iTrader: (17)
G12314 (Jimmy) setup was tested at the track very similar to Mikes Hobbyshop track...it is a 1/8th On Road circuit...so, it is very similar in size. I would lower the RPM by 1 notch, time delay is really depends on how long is the straight...the most is 0.1s faster then G12314 setup. And gear up 2 teeth or so if you are running 13.5T motor...
#5675
Tech Champion
Heys guys, possible dumb question of the day: Does a lower DRRS setting ever increase motor temps? Thought it should lower it some, but it doesn't seem to. 205G with 7.5~10.5, in a stadium truck.
#5677
Tech Champion
iTrader: (377)
Hello every one,got a race this Sunday in on-road 17.5 sedan and one of my friends gave me a Speed Passion LPF GranTourismo version 2.0 to use.Problem is that I never had a speedo with timing advance and boost option.The speedo comes with the multi ecs program card and the ''LCD professional program card'' as well.The track is a medium/small track ,perhaps 25 feet by 35 feet.Can anyone recommend a set up ? And in my instructions it states that for item number 3 (low voltage cut off) one should not use the default setting (value).I can use the program box to install the settings but as far as getting into custom profiles with the use of a lap-top,I think I will wait until I am more familiar with it.So if anyone can just post the numbers ,one through 15 I would really appreciate it.Thank you.
Last edited by peter george; 10-01-2010 at 11:53 PM.
#5678
Tech Regular
is it dangerous for the engine to drive 7:19 into FDR?
engine is a 17.5T v3. ESC SP Prostock 2.1 (528stock)
the engine is after 5 min at about 56 degrees celcius. top speed is like the mod.
have oil on bearings in the engine after each run
Absolutely wonderful power and speed
engine is a 17.5T v3. ESC SP Prostock 2.1 (528stock)
the engine is after 5 min at about 56 degrees celcius. top speed is like the mod.
have oil on bearings in the engine after each run
Absolutely wonderful power and speed
#5679
Tech Adept
Hi Solara, i'm using the standard m05 gearing i only have 3 options on gearing and i'm using the 20t pinion. I'm pretty sure the ratios are the same as the m03. I'll be trying it without boost to start with and if it can handle the power i'll try a little booost I just want a starting point for the esc settings then i'll go from there. I had a little go last night but the thermal protect kicked in after a couple of mins. I'll get the settings and post up when my friend brings my lcd box back.
#5680
Major problem! My car is going flat after about a minute. A green flashing light comes on and blinks.
#5681
I downloaded the 10.5 stock profile from the website and have nothing bit problems. Same gearing and all. 50c thunder power lipo.
#5682
I downloaded the 10.5 stock profile from the website and have nothing bit problems. Same gearing and all. 50c thunder power lipo.
#5684
It ran Just fine in practice this morning. Got ready for the first round and on the first lap I started down the straight and it just had no power at all
#5685
How is it possible to test the Hal sensor? Is this in the sensor end of the motor?