R/C Tech Forums - Search Results

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Community
Wiki Posts
Search
 
Search: Posts Made By: billtc3
Showing results 1 to 25 of 154
Search took 0.01 seconds.
06-17-2022, 04:12 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

Hi, the spring rate doesn't seem to be available....

Hi, the spring rate doesn't seem to be available.
The rattling noise might be from the diff gears. If you hit something too hard, or if you use a motor too powerful, the gears take a lot of stress...
05-27-2022, 04:17 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

When the diff rotates at thousands of rpm, grease...

When the diff rotates at thousands of rpm, grease slips away from the diff balls. The faster the motor, the faster the diff is drained out of grease. Then you have to rebuild the diff by opening it...
05-24-2022, 04:51 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

I race my pro4 13.5 blinky without any diff...

I race my pro4 13.5 blinky without any diff problems. Diff can last through a race. Rebuild after race.
...
05-24-2022, 04:47 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

The shocks are probably not long enough. The...

The shocks are probably not long enough. The original pro4 shock shafts were 32mm long. Perhaps the optional shocks you installed have shorter shafts. You could either install longer shafts, or...
03-19-2022, 08:28 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

So, that's a short video. It's the white/green...

So, that's a short video. It's the white/green Honda, not the blue car. It's alive! Setup changes pending and better quality video next time :)
03-19-2022, 08:19 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

https://youtu.be/3VqIEE_SOak

https://youtu.be/3VqIEE_SOak
03-19-2022, 08:17 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

https://cimg5.ibsrv.net/gimg/www.rctech.net-vbulle...

https://cimg5.ibsrv.net/gimg/www.rctech.net-vbulletin/2000x1124/20220307_144506_0e3fd9dc4c0a9ecdf11699ba733119ca041b3790.jpg
02-22-2022, 05:53 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

Yes! It keeps up with modern fwd cars very well....

Yes! It keeps up with modern fwd cars very well. I have to make a few setup adjustments, cause there is room for improvement. I promise to upload a video soon
10-19-2021, 02:45 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

Thank you so much for your kind words! In my area...

Thank you so much for your kind words! In my area we race 17.5 blinky. Once I hit the track, I will let you know if it is competitive against regular fwd cars
10-15-2021, 12:35 AM
Replies: 16,231
Views: 1,537,748
Posted By billtc3

This is a FWD made of spare pro4 parts. It was...

This is a FWD made of spare pro4 parts. It was really fun to build. It doesn't look like a home-made chassis, does it? Only extra parts used were Asso TC7 steering arms and Xray XB4 servo mount. The...
02-27-2020, 06:56 AM
Replies: 393
Views: 100,404
Posted By billtc3

a few are available in this European eshop ...

a few are available in this European eshop
https://www.racerc.gr/search?type=product&q=wildfire+arm
03-09-2016, 12:00 PM
Replies: 727
Views: 124,078
Posted By billtc3

Thank you all for the feedback on the CRC tires....

Thank you all for the feedback on the CRC tires. I was tempted to give them a try, but I would be disappointed. You saved me $60 :)

Here is an amateur video of my car. It is the white/green pro10....
03-09-2016, 04:44 AM
Replies: 5,982
Views: 1,599,332
Posted By billtc3

Hi, I was wondering if anybody has tried the new...

Hi, I was wondering if anybody has tried the new CRC slicks for pancars. Are they as competitive as traditional foams, or are they only good for bashing with slow motors? I race a 235mm pancar with a...
03-09-2016, 04:43 AM
Replies: 727
Views: 124,078
Posted By billtc3

Hi, I was wondering if anybody has tried the new...

Hi, I was wondering if anybody has tried the new CRC slicks for pancars. Are they as competitive as traditional foams, or are they only good for bashing with slow motors? I race a 235mm pancar with a...
11-04-2015, 01:39 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

One quick question about the VST black edition...

One quick question about the VST black edition motors: Are the rotors sintered or bonded? Thnks!
05-06-2014, 07:09 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

@ Bob and Dave Thank you for your replies. I...

@ Bob and Dave

Thank you for your replies. I don't have a progauge so I can't tell which firmware version my esc has ended up with. Anyway, it still works great, as it did before the upgrade, so I...
05-04-2014, 11:50 PM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

@Wildcat1971 Who are you? Are you a Viper...

@Wildcat1971

Who are you? Are you a Viper representative? If not, please stop replying to my posts. I would rather have somebody from Viper reply, one who can read English, who can write English...
05-04-2014, 12:05 PM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

Please read: "...Check out the attached...

Please read:

"...Check out the attached screenshot from the youtube video,..."

The attached screenshot is from the youtube video, like I said, not from my vlink.... :rolleyes:

Nikos, if it...
05-04-2014, 09:11 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

I found this video on youtube: ...

I found this video on youtube:
http://www.youtube.com/watch?v=GWGG_QR9TrY

I have downloaded the correct file (ViperVLink_VTX10_10R_A64_For Black Edition Only_Release) and I followed the steps as...
05-03-2014, 11:38 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

I have a 10R black edition that I just updated to...

I have a 10R black edition that I just updated to the A64. The "problem" is that after I update (I get the "update completed" message), the next time I connect the esc to my pc and launch the...
04-01-2014, 03:23 AM
Replies: 4
Views: 1,129
Posted By billtc3

In a few words: - Always try to keep front and...

In a few words:
- Always try to keep front and rear links in similar length and angle. This should make the car more progressive and predictable under all circumstances.
- Long / parallel links...
02-25-2014, 03:14 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

@ nikos2002 Hi Nikos, I have a VTX10R BE esc...

@ nikos2002

Hi Nikos, I have a VTX10R BE esc and a VST2.5T motor. I set up my esc on program 6 (modified blinky), my motor on default mechanical timing and I run them in a 1/10 touring car on a...
10-10-2013, 03:56 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

nikos2002, what is the motor limit of the...

nikos2002,

what is the motor limit of the VTX1 for 1 cell 1/12 scale racing?

thanx
12-22-2012, 07:03 AM
Replies: 1,534
Views: 182,300
Posted By billtc3

I want to run a VST 4.5T motor on a large outdoor...

I want to run a VST 4.5T motor on a large outdoor track, where high RPM is more important than torque. As I understand, the 4.5T comes with a 12.3mm rotor and a fan.

- Should I remove the fan form...
12-22-2012, 03:03 AM
Replies: 12,070
Views: 1,204,949
Posted By billtc3

I want to run a VST 4.5T motor on a large outdoor...

I want to run a VST 4.5T motor on a large outdoor track, where high RPM is more important than torque. As I understand, the 4.5T comes with a 12.3mm rotor and a fan.

- Should I remove the fan...
Showing results 1 to 25 of 154
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.