New 1/8th 4WD basic class ???!!!
#121
Tech Apprentice
Servo saver.
Buri has already installed ball bearings.
Buri has already installed ball bearings.
#122
Tech Apprentice
Chassis without electronics.
#123
awesome thank you so much for the photos very much appreciated
#124
Tech Apprentice
thats a great looking car and a great idea, may be a tough sell at my "nitro only"track. 2 things holding me back are 1 the weak candian dollar makes it cost like a 4wd nitro. 2 no power at my track what have others with no power done?
#125
1/8th electric stock class will be established
The BURI-Racer E1 is a very simple 1/8th electric chassis.
We are discussing to run these cars in an 1/8th electric stock class in several european countries besides an open (unlimited) class. In the stock class there will be a motor limit with 1900ky and batteries with 4s.
But dont think the BURI-Racers are slow! Look at the videos of the indoor race in Friedrichshafen - the laptimes were nearly the same as in the modified class!
my youtube-channel: BURI-Racer
Assembling a BURI-Racer E1: no special tools needed, no oil for shock absorbers or differential (because there is no one We finish the chassis within 2 hours
We are discussing to run these cars in an 1/8th electric stock class in several european countries besides an open (unlimited) class. In the stock class there will be a motor limit with 1900ky and batteries with 4s.
But dont think the BURI-Racers are slow! Look at the videos of the indoor race in Friedrichshafen - the laptimes were nearly the same as in the modified class!
my youtube-channel: BURI-Racer
Assembling a BURI-Racer E1: no special tools needed, no oil for shock absorbers or differential (because there is no one We finish the chassis within 2 hours
#126
Tech Master
Where are you guys getting these cars in the United States??
#127
There would always be the option to convert to gas! Tom has developed a gas version and we could go that route!!
Ned
#128
Tech Apprentice
Joe,I was ready to get one but like you the price seems to be quite a bit high...the charging should not be a problem a car battery and maybe a little Harbor Freight Generator (>$100usd) should work fine.
There would always be the option to convert to gas! Tom has developed a gas version and we could go that route!!
Ned
There would always be the option to convert to gas! Tom has developed a gas version and we could go that route!!
Ned
#129
Hi,
about export to US:
Single shipments are expansive, because each parcel has an import fee of minimum 25 U$ and I have to ship with an international forwarding agent.
Another problem are the US restriction and laws, that doesnt make the business easy.
The consumer price of the roller within Europe is 350.00 € (thats including VAT, in Austria 20%), so without VAT its 291.00 €
I dont know the taxes you have to pay in the States.....
Besides: to compare you have to look at the whole car. For the BURI-Racer i calculate:
roller 350.00
motor 68.00 (SkyRC Toro X8)
esc 89.00 (Hobbywing WP-SC8)
battery 75.00 (LiPo 4s 5000mAh 30c)
total: 582.00 again incl. VAT
Thats expansive? If you calculate a Serpent977e you will not end below 1500.00€ !
Is there any dealer interested to import the BURI-Racer to the States? I am still searching. Please PM
Best regards Thomas
about export to US:
Single shipments are expansive, because each parcel has an import fee of minimum 25 U$ and I have to ship with an international forwarding agent.
Another problem are the US restriction and laws, that doesnt make the business easy.
The consumer price of the roller within Europe is 350.00 € (thats including VAT, in Austria 20%), so without VAT its 291.00 €
I dont know the taxes you have to pay in the States.....
Besides: to compare you have to look at the whole car. For the BURI-Racer i calculate:
roller 350.00
motor 68.00 (SkyRC Toro X8)
esc 89.00 (Hobbywing WP-SC8)
battery 75.00 (LiPo 4s 5000mAh 30c)
total: 582.00 again incl. VAT
Thats expansive? If you calculate a Serpent977e you will not end below 1500.00€ !
Is there any dealer interested to import the BURI-Racer to the States? I am still searching. Please PM
Best regards Thomas
Last edited by TomAT; 12-01-2015 at 11:08 PM.
#130
Tech Apprentice
Hi,
about export to US:
Single shipments are expansive, because each parcel has an import fee of minimum 25 U$ and I have to ship with an international forwarding agent.
Another problem are the US restriction and laws, that doesnt make the business easy.
The consumer price of the roller within Europe is 350.00 € (thats including VAT, in Austria 20%), so without VAT its 291.00 €
I dont know the taxes you have to pay in the States.....
Besides: to compare you have to look at the whole car. For the BURI-Racer i calculate:
roller 350.00
motor 68.00 (SkyRC Toro X8)
esc 89.00 (Hobbywing WP-SC8)
battery 75.00 (LiPo 4s 5000mAh 30c)
total: 582.00 again incl. VAT
Thats expansive? If you calculate a Serpent977e you will not end below 1500.00€ !
Is there any dealer interested to import the BURI-Racer to the States? I am still searching. Please PM
Best regards Thomas
about export to US:
Single shipments are expansive, because each parcel has an import fee of minimum 25 U$ and I have to ship with an international forwarding agent.
Another problem are the US restriction and laws, that doesnt make the business easy.
The consumer price of the roller within Europe is 350.00 € (thats including VAT, in Austria 20%), so without VAT its 291.00 €
I dont know the taxes you have to pay in the States.....
Besides: to compare you have to look at the whole car. For the BURI-Racer i calculate:
roller 350.00
motor 68.00 (SkyRC Toro X8)
esc 89.00 (Hobbywing WP-SC8)
battery 75.00 (LiPo 4s 5000mAh 30c)
total: 582.00 again incl. VAT
Thats expansive? If you calculate a Serpent977e you will not end below 1500.00€ !
Is there any dealer interested to import the BURI-Racer to the States? I am still searching. Please PM
Best regards Thomas
#131
#133
Tech Champion
iTrader: (102)
I am going to play with a body with less down force.
Last edited by 1/8 IC Fan; 12-12-2015 at 10:36 AM.
#135
I have some questions about the electronics...
How much weight the car without electronics (but with tyres)...¨
I can see thta most of the people are running 4s with 1/8 electronics. I was thinking about using the car as light as possible... Is it possible to mount a 540 motor on the E1?
My objective would be to run the car with 2s or 3s with a TS160 and 540 motor (2 poles or 4 poles)
Do you think it would be possible?
How much weight the car without electronics (but with tyres)...¨
I can see thta most of the people are running 4s with 1/8 electronics. I was thinking about using the car as light as possible... Is it possible to mount a 540 motor on the E1?
My objective would be to run the car with 2s or 3s with a TS160 and 540 motor (2 poles or 4 poles)
Do you think it would be possible?