NEW HB comp touring
#136
.
Last edited by Adrean; 01-23-2013 at 07:21 PM.
#137
I'm more concerned about the nitro which may fall into the receiver as per the exhaust heat .
Last edited by Adrean; 01-23-2013 at 07:21 PM.
#138
Ok Guys i just have to say this car its Amazing ! i just have my first run with it in my local championship and i Won by 5 laps , put a track record , and my car finish like new ! i run with standard setup with minor changes to Tires and ride height !
Here are the Pics of my car after the Final , and a Podium Pic .
Im very pleased with my car performance !!!
Cheers From Mexico
Here are the Pics of my car after the Final , and a Podium Pic .
Im very pleased with my car performance !!!
Cheers From Mexico
#141
..........
Last edited by 1evo RRR Driver; 02-01-2013 at 09:39 AM.
#142
Theres alot going on around your steering servo! (rats nest) Doesn't look like a well planned out design for electronics! I highly dought anyone would put there $100+ receiver that close to a 300° exhaust pipe.....worst deck design I've seen in a while, but car seems to work well on track..i guess that's all that matters!! Lol
#143
Tech Initiate
Have anyone tried to fit the parts used by HB team drivers at the WC? Seems like Capricorn parts.
#144
#145
If that part of the top plate holding the servo saver was made a 1 piece top deck it would almost an exact replica of the v one rrr, and if I'm not mistaking the designer of the car designed the RRR also.. The rear shock tower and front upper arms too look like from the kyosho IMO.. Kyosho was and still is an awesome car this is like an upgraded version if you ask me, but not a bad thing
#146
If that part of the top plate holding the servo saver was made a 1 piece top deck it would almost an exact replica of the v one rrr, and if I'm not mistaking the designer of the car designed the RRR also.. The rear shock tower and front upper arms too look like from the kyosho IMO.. Kyosho was and still is an awesome car this is like an upgraded version if you ask me, but not a bad thing
#147
If it works like a RRR, this car for sure will be my next since I'm still using my RRR with a few mods to make it more modern like, R4 front diff, KM top deck with nt1 gas tank and km racing roll center bridge.. I'm hoping this car works like a RRR and hope someone at my track purchased this car so I can see it run this summer, the car is tempting nevertheless
#148
Hello.
I just bought a couple of R10:s and have some questionmarks on what option parts fit the car:
1. I want to use plastic pulleys, xrays/capricorn seem to fit but what Light-Weight 2-speed shaft can I use and what brakerotor pulley would fit?
2. What good ventilated brake disk might fit?
3. Pivotballs are 8mm, I want som ti or alu balls - does anyone know who might be making these? Are the Mugen MTX5-balls 8mm?
4. Low friction belts?
I just bought a couple of R10:s and have some questionmarks on what option parts fit the car:
1. I want to use plastic pulleys, xrays/capricorn seem to fit but what Light-Weight 2-speed shaft can I use and what brakerotor pulley would fit?
2. What good ventilated brake disk might fit?
3. Pivotballs are 8mm, I want som ti or alu balls - does anyone know who might be making these? Are the Mugen MTX5-balls 8mm?
4. Low friction belts?
Last edited by Ec1; 03-07-2013 at 05:46 AM.
#149
Tech Elite
iTrader: (11)
A nice little price increase in the price for an R10 kit in the US since Hobbico/Great Planes Model took over as distributors. Both A Main and Tower have jumped from $650us to $1043us dollars....
Its now the most expensive 10th scale you can buy... People thought the Capricorn was expensive!
Its now the most expensive 10th scale you can buy... People thought the Capricorn was expensive!