Lab C-02
#407
Tech Addict
Protoform SRS-N on Black Edition
Dear all,
Which body post holes are you using as for height of the SRS and do you shave the foam bumper to make it fit? Or you move the body more upfront?
Thanks
Which body post holes are you using as for height of the SRS and do you shave the foam bumper to make it fit? Or you move the body more upfront?
Thanks
#409
Tech Master
iTrader: (2)
Regarding the height, I cut it following the trimline and then make sure it doesn't hit the ground when on track.
I think the SRS is the only body which actually has a usable trimline.
#410
Tech Addict
I mount mine 4mm forward. To me this gives a nicely balanced car with the wing all the way back (10mm).
Regarding the height, I cut it following the trimline and then make sure it doesn't hit the ground when on track.
I think the SRS is the only body which actually has a usable trimline.
Regarding the height, I cut it following the trimline and then make sure it doesn't hit the ground when on track.
I think the SRS is the only body which actually has a usable trimline.
#411
Tech Addict
Black edition setup help
Hey guys, so have been running the Black edition and have it on rails, fastest lap time and i can feel the car to be a bit superior than the competition, its practically stock items, what i have changed is a step harder front shocks and 8 hole piston in the rear shock with 1300 allround
Also used the new clutch reversed system and found it better than the normal one. Smoother take off!
So you might be saying whats my problem, basically during practice and qualification the car is .50 per lap slower (avg lap 19.2sec) and very hard to drive (unstable). My biggest concern is that in chicanes the car understeers and on some others tight turns it oversteers heavily that i loose control its also very twitchy. How am i going to sort this out.
They prep the track by sugar and water and from how i set the brake i have noticed that track is very slippery early in the morning.
Suggestions plz
Thanks
Also used the new clutch reversed system and found it better than the normal one. Smoother take off!
So you might be saying whats my problem, basically during practice and qualification the car is .50 per lap slower (avg lap 19.2sec) and very hard to drive (unstable). My biggest concern is that in chicanes the car understeers and on some others tight turns it oversteers heavily that i loose control its also very twitchy. How am i going to sort this out.
They prep the track by sugar and water and from how i set the brake i have noticed that track is very slippery early in the morning.
Suggestions plz
Thanks
#412
C02 BE + M3 WCS
Take a look, first practice this year with C02 Black Edition and REDS M3 WCS engine
https://www.facebook.com/#!/rc.netshop.dk
All the best,
Niko
https://www.facebook.com/#!/rc.netshop.dk
All the best,
Niko
#413
Tech Master
iTrader: (37)
Take a look, first practice this year with C02 Black Edition and REDS M3 WCS engine
https://www.facebook.com/#!/rc.netshop.dk
All the best,
Niko
https://www.facebook.com/#!/rc.netshop.dk
All the best,
Niko
#414
Take a look, first practice this year with C02 Black Edition and REDS M3 WCS engine
https://www.facebook.com/#!/rc.netshop.dk
All the best,
Niko
https://www.facebook.com/#!/rc.netshop.dk
All the best,
Niko
Ran with a friend that only runs reds last week. Fast, fast, fast
#415
Tech Master
iTrader: (37)
What springs (spring rate) come with the big bore shocks in the Black Edition kit? There's no making and/or number to determine what they are. It does appear that all 4 are the same.
Also, my 2 speed gear assembly has a good amount of side by side play (approx 1-1.5mm) when it's installed in the rear transmission. I built/measured per the instructions. Did I do something wrong? Is this normal or should I shim this out?
Thanks in advance guys.
Also, my 2 speed gear assembly has a good amount of side by side play (approx 1-1.5mm) when it's installed in the rear transmission. I built/measured per the instructions. Did I do something wrong? Is this normal or should I shim this out?
Thanks in advance guys.
#416
#417
What springs (spring rate) come with the big bore shocks in the Black Edition kit? There's no making and/or number to determine what they are. It does appear that all 4 are the same.
Also, my 2 speed gear assembly has a good amount of side by side play (approx 1-1.5mm) when it's installed in the rear transmission. I built/measured per the instructions. Did I do something wrong? Is this normal or should I shim this out?
Thanks in advance guys.
Also, my 2 speed gear assembly has a good amount of side by side play (approx 1-1.5mm) when it's installed in the rear transmission. I built/measured per the instructions. Did I do something wrong? Is this normal or should I shim this out?
Thanks in advance guys.
I will check for you, can't remember what springs it is in the BE kit :-)...
I also got a bit of play, but shims it up a bit. I make so I just have a little play and all is running freely