help !about mugen 1:8 on-road brake pad
:flaming: I bought a mugen mrx4 few days ago.When assemblng it ,I find brake pad is so tight that the car can't move at all.Please tell me how to deal with it ? :flaming: :flaming:
|
Screws hold it on, loosen them.
|
:eek:
|
re all
I learn serpent 960'manual ,it says roughen the metal plate with sandpaper before guling.Must I roughen mugen's before assembling?help me
|
re you
Originally Posted by Artificial-I
Screws hold it on, loosen them.
|
brake
Make sure the rear pulley is not to far to the brake side.
|
I understand that there is a certain way to glue the brake pads to the metal pads. If you glue it wrong it will cause serious binding. :weird:
|
havent seen the instructions, but what Artificial-I said is a good starting point. :)
Originally Posted by Artificial-I
Screws hold it on, loosen them.
|
Originally Posted by hyl
:flaming: I bought a mugen mrx4 few days ago.When assemblng it ,I find brake pad is so tight that the car can't move at all.Please tell me how to deal with it ? :flaming: :flaming:
1) The pin that hold the metal and pad has to be free of glue residue and that the pads are not upside down meaning the top and bottom of the pad matches with the shape of the metal. if it is the pads itself will bind on that pin and it will be tight, it will be harder for it to slide. 2) make sure that the disc is seated straight on the three prong attached to the pulley. in time it will loosen up but for now check by rotating the shaft or rear wheel .look at it while rotating and you will see if you have a bind. if you have one try to move it around by a screwdriver against the pulley and twist gently until it is smooth. 3) please make sure that your brake post is not reversed. I meant that the flat side is facing the metal of the pads. good luck!!!! enjoy... Check your instruction and you will see and understand what I am saying |
re all
"a certain way to glue the brake pads to the metal pads" I know .But I carefully read the manual,I don't find any mistakes!!!
|
Originally Posted by hyl
"a certain way to glue the brake pads to the metal pads" I know .But I carefully read the manual,I don't find any mistakes!!!
jus wondering, did you sand down your brake pads? :D |
Originally Posted by hyl
"a certain way to glue the brake pads to the metal pads" I know .But I carefully read the manual,I don't find any mistakes!!!
|
Originally Posted by RCRjuanabbe
three things you need to check:
1) The pin that hold the metal and pad has to be free of glue residue and that the pads are not upside down meaning the top and bottom of the pad matches with the shape of the metal. if it is the pads itself will bind on that pin and it will be tight, it will be harder for it to slide. 2) make sure that the disc is seated straight on the three prong attached to the pulley. in time it will loosen up but for now check by rotating the shaft or rear wheel .look at it while rotating and you will see if you have a bind. if you have one try to move it around by a screwdriver against the pulley and twist gently until it is smooth. 3) please make sure that your brake post is not reversed. I meant that the flat side is facing the metal of the pads. good luck!!!! enjoy... Check your instruction and you will see and understand what I am saying 4. There is a top and a bottom for the brake plates. If this isn't correct, the brake plates will bind. 5. Make sure the holes in the brake plate/pad assembly are free from glue. I open up these holes so they slide easily on the pins. 6. Most likely you have used too much glue to adhere the pads to the plates. There is only so much room between the brake post and the stops. Sand down the pad material until each pad/plate is approximately 2.1 mm and make sure they are flat and parallel. |
Seems like everyone is pointing you in the right direction. The issue with the pads having a top and bottom is something to check, I know because I have assembled the rear end on my MRX4 many times. I would not sand the pads to much after assembly because if you run the car you want the pads to seat properly. The pads should only slightly touch the disc with some play until engaged. Sounds like you need to check your rear end/brake assembling.
|
Originally Posted by kmh
(Post 7404652)
Seems like everyone is pointing you in the right direction. The issue with the pads having a top and bottom is something to check, I know because I have assembled the rear end on my MRX4 many times. I would not sand the pads to much after assembly because if you run the car you want the pads to seat properly. The pads should only slightly touch the disc with some play until engaged. Sounds like you need to check your rear end/brake assembling.
|
All times are GMT -7. It is currently 10:35 PM. |
Powered By: vBulletin v3.9.3.8
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.