trinity reflex
#106
Tech Elite
fastharry;
Unless they've moved the Receiver mounting, I WON'T be getting one soon. One side hit and your day is over. I honestly can't think of a single race where I haven't been side impacted by SOMEONE once during the day.
tony montana;
Yes they will fit.
Unless they've moved the Receiver mounting, I WON'T be getting one soon. One side hit and your day is over. I honestly can't think of a single race where I haven't been side impacted by SOMEONE once during the day.
tony montana;
Yes they will fit.
#109
Tech Apprentice
hey guys, i have a reflex roller if someone is interested. just needs a fuel tank. got pics if you need. $180 takes it. [email protected]
#110
Tech Elite
Originally posted by tony montana
popsracer do you have part#'s for the v1r pullies and belts?
popsracer do you have part#'s for the v1r pullies and belts?
The part # for the Pulleys is a few posts up and the PN for the belts has be posted several times in this thread. I'm sure if you read back a few Posts you can find them.
#113
Tech Elite
need help two speed
td-civ;
Set-up the 2 spd exactly as the Manual recommends, then adjust the shift point screws 6 turns out to start with. A 1/2 a turn either way after that should get you where you need to be.
If you playing in the Street, just about any Servo will do. For Serious racing a High Speed Digital is the way to go. Keep an Analog servo for the Throttle/Brake and stay away from the Hitec (5)625/645 series Servo's. I've had 3 that have been NOTHING but trouble.
Set-up the 2 spd exactly as the Manual recommends, then adjust the shift point screws 6 turns out to start with. A 1/2 a turn either way after that should get you where you need to be.
If you playing in the Street, just about any Servo will do. For Serious racing a High Speed Digital is the way to go. Keep an Analog servo for the Throttle/Brake and stay away from the Hitec (5)625/645 series Servo's. I've had 3 that have been NOTHING but trouble.
#114
go for a KO PDS 2143 FET servo.. thats what i have and it works sweet super fast (0.08sec) and 8kg's of torque
#115
popsracer
are you using the Trinity pinon and spur gears on there centex ?
What all do i need I'm gonig to try it..
Thanks
What all do i need I'm gonig to try it..
Thanks
#116
Tech Elite
Mugen Centax on the Reflex
THeGame;
The MTX-3 Centax kit comes complete except for the Pinions and the Mugen and Reflex pinions will both fit. The 1/8th Pinions have the same tooth pattern as the Reflex, the MTX-3 pinions are "Different" but will work.
No matter what, I would space the 1st gear Pinion out to mesh fully with the Reflex Spurs.
To do this you will need some kind of spacer. I used an Aluminum Oil Pan Gasket washer and ground the OD below the tooth level of 2nd gear. (was just my preference)
The person who told me about the MTX-3 clutch and says he uses it with the Factory Pinion spacing and has never had a problem. I also needed more total shims than were included in the kit, so you may too depending on your flywheel spacing.
Use the Centax Clutch set-up instructions on the Team Trinity website. They were spot on perfect for me.
The MTX-3 Centax kit comes complete except for the Pinions and the Mugen and Reflex pinions will both fit. The 1/8th Pinions have the same tooth pattern as the Reflex, the MTX-3 pinions are "Different" but will work.
No matter what, I would space the 1st gear Pinion out to mesh fully with the Reflex Spurs.
To do this you will need some kind of spacer. I used an Aluminum Oil Pan Gasket washer and ground the OD below the tooth level of 2nd gear. (was just my preference)
The person who told me about the MTX-3 clutch and says he uses it with the Factory Pinion spacing and has never had a problem. I also needed more total shims than were included in the kit, so you may too depending on your flywheel spacing.
Use the Centax Clutch set-up instructions on the Team Trinity website. They were spot on perfect for me.
Last edited by popsracer; 05-04-2003 at 10:32 PM.
#118
i got my KO servo for 147 AUD delivered from hong kong so i guess it would be something like 80 maybe 90 USD.... depends where you look for them but they are worth every cent trust me!