i need some help with this
#16
Tech Master
i dont even think they make a steel spur gear(im not sure though) because it would add a ton of roataing mass and therefore decrease acceleration jarasticly and in the 2 years i have been racing i've only stripped around 2 spurs so your best off with plastic
#17
yea i wasnt sure about that but i thought i saw one before.
#18
Tech Master
i noticed that the charger you picked out was dc only so u have to run it from a 12v power source such as a car battery or power supply
#19
o crap im happy i didnt buy that yet lol thanks... but everything else will work together right.......
#20
will this 1 workhttp://www2.towerhobbies.com/cgi-bin...?&I=LXWL89&P=7
with this batteryhttp://www2.towerhobbies.com/cgi-bin...?&I=LXGJP9&P=M
with this batteryhttp://www2.towerhobbies.com/cgi-bin...?&I=LXGJP9&P=M
#21
Tech Master
yup they will work together the only thing is the conectors may not be the same so u may need an adaptor but thats about it you may not even need the adaptor
#22
tech forums i sthe best i never got this many reply on other forums thanks alot for u help when im done with my car il poast a pic of it or ill send u one.
#23
sry i cant type ill post a pic when im done with it or send it to u by email.thanks again
#24
Originally posted by Javen13
the tc3 stock comes with a 72 spur so u will have to order a pinion for the motor i would by 3 or 4 pinions to experement with maybe in the 18-24 range if u want top speed
the tc3 stock comes with a 72 spur so u will have to order a pinion for the motor i would by 3 or 4 pinions to experement with maybe in the 18-24 range if u want top speed
At my local outdoor track (average sized) in a TC3 anything under 32 teeth is considerd undergeard.
#25
Tech Master
the tc3 comes with 48 pitch spur gear were u race they most likely use 64 pitch because on my tc3 i run 64 pitch and run a 33 tooth pinion so a 22 in 48 is evual to like a 37 or so in 64 pitch
#26
so like a 35/40 umm i really am bad at gearing really bad ok so if im wrong tell me. thanks!!!!!!
#27
Originally posted by X2
A 24 tooth for top speed? Thats REALLY small, I take it you race indoors or on a small track all of the time?
At my local outdoor track (average sized) in a TC3 anything under 32 teeth is considerd undergeard.
A 24 tooth for top speed? Thats REALLY small, I take it you race indoors or on a small track all of the time?
At my local outdoor track (average sized) in a TC3 anything under 32 teeth is considerd undergeard.
at least not in mine..
#28
Tech Champion
i kno the highest 48p pinion i put in with a 72t spur was a 31...i dont remember tryin much more than that....i have also had some work done to the motor mounting cam, but that was after i ran 31t pinions
#29
like 4 a novak brushless what should i do...sry.. i ask alot a questions!!it is this model her is the pic but it only shows the esc the motor specs r at the bottomhttp://www2.towerhobbies.com/cgi-bin...8&I=LXDDD7&P=K thanks so much for helpin me out this long!!!!!
#30
Tech Master
for the brush less you may want to try a 27 or so to start with i think its robison racing that sells all the odd or all the even pinion numbers so u may want to try that