Tekin RS ESC sensored
09-05-2008, 09:30 AM
#962
Not an issue but it does seem to happen with Futaba's high speed receivers (the FASST system is even faster than HRS if i'm not mistaken), it's known and actually in the manual in the troubleshooting section it tells you to reverse if the speedo doesn't take radio calibration.
09-05-2008, 09:35 AM
#963
Tech Master
I only get the first screen were i can choose between update help and exit. above it it shows the hotwire connection withe the esc connection.
There i can't change the update. I don't come in the next sceen. I can only com in the next screen when he sees my esc but there is no connection with my esc. i don't get anny connection with my esc. only with my hotwire and then it keeps asking to connect my esc. furter i don't com.
There i can't change the update. I don't come in the next sceen. I can only com in the next screen when he sees my esc but there is no connection with my esc. i don't get anny connection with my esc. only with my hotwire and then it keeps asking to connect my esc. furter i don't com.
09-05-2008, 09:38 AM
#964
Tech Master
i don't come in the rs screen. only in the first hotwire screen.
09-05-2008, 09:45 AM
#965
Mikky:
Do you get any type of change when you plug in the RS into the Hotwire?
When you plug in your RS to the hotwire do any of the rs's led's light up? If so which ones?
Do you get any type of change when you plug in the RS into the Hotwire?
When you plug in your RS to the hotwire do any of the rs's led's light up? If so which ones?
09-05-2008, 09:52 AM
#966
Tech Master
No nothing changes.
also not on my hotwire. that stays on green and the redligts after the green one shine a litle bit.
also not on my hotwire. that stays on green and the redligts after the green one shine a litle bit.
09-05-2008, 09:55 AM
#967
My RS Pro and hotwire arrived today (- Thank you RC Market!).
My next race meeting is on Thursday so might have to wait awhile before putting it through its paces but I may get some practice in on Saturday if i'm lucky! Gonna try it on sensored only mode to start with with my Novak 10.5 then switch to dual mode and play with timing.
Can't believe its so small! - fits nicely on my xray 008!
Just had one issue though - it would only calibrate when the throttle revere on the transmitter was in reverse mode, not normal! Is this a problem?
Any other recommendations before my first outing?
Thanks
Paul
My next race meeting is on Thursday so might have to wait awhile before putting it through its paces but I may get some practice in on Saturday if i'm lucky! Gonna try it on sensored only mode to start with with my Novak 10.5 then switch to dual mode and play with timing.
Can't believe its so small! - fits nicely on my xray 008!
Just had one issue though - it would only calibrate when the throttle revere on the transmitter was in reverse mode, not normal! Is this a problem?
Any other recommendations before my first outing?
Thanks
Paul
Thanks !
no Problem !
dual cap. or Higher cap. ( around 2200uf )
Best Regards,
09-05-2008, 09:59 AM
#968
I'm no specialist in the matter but from what you described, and how it happened, I think your update went badly wrong and your speedo ended up not having or having an incomplete firmware. As a result the hotwire doesn't recognises the speedo as being an RS and obviously the speedo won't boot up properly when plugged in. Unless Randy and Jim have a solution to force a firmware update then my opinion is that you should fill up the CS return form and send your speedo back.
09-05-2008, 10:00 AM
#969
Tech Master
I got mine also from rcmarket. somting went wrong with the post here but lukkely rcmarket helpt me and sendet it back.
Thanks for your help. great sevice.
But what must i do now?
I don't get anny connection to mine esc with the pc and it's also not working.
Must i send it to Tekin? Howlong does it thake till i get it back when i do sow and how manny will cost me that for sending?
I reciefed my teking wensday so it's in the 120days waarenty.
Will it be fikst before the 14th so i can race with it?
Thanks for your help. great sevice.
But what must i do now?
I don't get anny connection to mine esc with the pc and it's also not working.
Must i send it to Tekin? Howlong does it thake till i get it back when i do sow and how manny will cost me that for sending?
I reciefed my teking wensday so it's in the 120days waarenty.
Will it be fikst before the 14th so i can race with it?
09-05-2008, 10:29 AM
#970
09-05-2008, 10:43 AM
#972
09-05-2008, 11:41 AM
#973
I have a futaba 3pk w/ spektrum and I also had to reverse my throttle in order to complete setup with both my Rs and Rs pro. In the manual for the mamba max, it explicitly notes that you will have to reverse the throttle on futaba radios to work. Must be a similar case
09-05-2008, 12:31 PM
#974
Call Tekin dirrectly and ask to talk to Charlie. I had the same problem. Your Hotwire has old drivers installed and your computer doesn't recognize it because the software you install dosn't match the hardware. Charlie will help you reconfigure the hardware to get it working with the software. He stepped me through it and I would have never figured it out myself.
09-05-2008, 12:46 PM
#975
Sorry for the delayed posting above guys, something up with my pc!
Thanks for the heads up, guess i was so excited I didn't read the manual fully otherwise I would have read the troubleshooting bit!
Anyway, will post later how I get on with it next week.
Cheers
Paul
Thanks for the heads up, guess i was so excited I didn't read the manual fully otherwise I would have read the troubleshooting bit!
Anyway, will post later how I get on with it next week.
Cheers
Paul