pro3
#1486
Tech Elite
iTrader: (1)
Re: ??? Just a piece of C/F?
Originally posted by JDM_DOHC_SiR
What do you mean..??? where there any holes drilled??
-Dave
What do you mean..??? where there any holes drilled??
-Dave
#1487
Tech Champion
iTrader: (31)
Re: solid hpi pro 3 arms...?
Originally posted by nozauta619
hey JDM-DOCH-SiR,
what type of suspension arms are you running with on your hpi pro3? is it delrin plastic or composite graphite? looks really cool & durable i want one too!!!
hey JDM-DOCH-SiR,
what type of suspension arms are you running with on your hpi pro3? is it delrin plastic or composite graphite? looks really cool & durable i want one too!!!
The A-arms are made by Square and the they are really durable and arm made of durable Nylon I have had the HPI composite graphite one and I have kept breaking then right where the hinge pin goes throught the A-arm So I switched to the Square Arms and Have had no problems since
-Dave
#1488
Tech Champion
iTrader: (31)
Re: Re: ??? Just a piece of C/F?
Originally posted by lee82gx
yes there where holes but no screws or spacers.which hole should i mount on?i heard that u shouldnt mount on steering posts....and do u remove the front bulkhead -rear?
yes there where holes but no screws or spacers.which hole should i mount on?i heard that u shouldnt mount on steering posts....and do u remove the front bulkhead -rear?
It might look like that in the pic but it's not that way..
also you will need 2 10mm bolts and 2 20mm bolts for up front
-Dave
#1490
Tech Addict
rc- do you or anyone else have a high bite asphult setup? for stock.
Thanks
Thanks
#1491
Tech Elite
Originally posted by teamAE
rc- do you or anyone else have a high bite asphult setup? for stock.
Thanks
rc- do you or anyone else have a high bite asphult setup? for stock.
Thanks
#1493
camber links
on, the Pro 3
by mounting the front camber link on the outer lower hole of the shock tower. do you get more or less steering???
Thanks!
by mounting the front camber link on the outer lower hole of the shock tower. do you get more or less steering???
Thanks!
#1494
Tech Elite
Asphalt/Rubber set-up
Front;
Shocks #6847 Green springs, 45wt oil, mounting A-2. Take-off 27CS premounted tires/wheels, 6 deg caster, 0 deg kick-up, -1 deg camber in position B-3. Zero front toe, Front one-way Diff, Front (black) swaybar. Ride height 4.5mm.
Rear;
Shocks #6844 Red springs, 40wt oil, mounting A-2. Take-off 27CS tires/wheels, -1 deg camber in position B-3, 2 deg toe-in (2-2-9)
Ride height 5.0mm
Chassis;
Stock HPI USA plastic chassis, HPI Graphite upper deck, HPI Graphite shock towers F & R. Monster Stock motor geared 116/33
Side note:
I had to go 2 steps softer overall with the springs after installing the Upper Deck.
For NEXT weekends race I will be changing to 3 deg caster blocks with 2 deg of kick-up. Hopefully to gain a little more on power steering.
Shocks #6847 Green springs, 45wt oil, mounting A-2. Take-off 27CS premounted tires/wheels, 6 deg caster, 0 deg kick-up, -1 deg camber in position B-3. Zero front toe, Front one-way Diff, Front (black) swaybar. Ride height 4.5mm.
Rear;
Shocks #6844 Red springs, 40wt oil, mounting A-2. Take-off 27CS tires/wheels, -1 deg camber in position B-3, 2 deg toe-in (2-2-9)
Ride height 5.0mm
Chassis;
Stock HPI USA plastic chassis, HPI Graphite upper deck, HPI Graphite shock towers F & R. Monster Stock motor geared 116/33
Side note:
I had to go 2 steps softer overall with the springs after installing the Upper Deck.
For NEXT weekends race I will be changing to 3 deg caster blocks with 2 deg of kick-up. Hopefully to gain a little more on power steering.
Last edited by popsracer; 01-16-2003 at 10:31 PM.
#1495
Tech Addict
thanks pops I will give it a try tomorow.
#1497
Re: camber links
Originally posted by racer
by mounting the front camber link on the outer lower hole of the shock tower. do you get more or less steering???
by mounting the front camber link on the outer lower hole of the shock tower. do you get more or less steering???
#1499
ttt