Team Magic E4 Thread
#3781
Tech Master
iTrader: (18)
i got my pack to fit it was a pain im the a$$ but its in cant run it yet as one of the arms are cracked so i need to get some
if you guys have extra lower arms front and back that your willing to sell and any other parts that i wi;ll need as back up let em know ill buy them off you guys
here is the list of k factory part im going to buy let me know if there is anything more i should get
7075 Adjustable Single Bell Crank Steering Set (k2121)
E4 Alum. 7075 Steering Block Set (k2110)
E4 Alum. 7075 Middle Shaft Mount (k2103)
E4 Alum.7075 Rear Bulkhead Upper Mount (k2144)
E4 Alum.7075 Front Bulkhead Upper Mount (k2143)
if you guys have extra lower arms front and back that your willing to sell and any other parts that i wi;ll need as back up let em know ill buy them off you guys
here is the list of k factory part im going to buy let me know if there is anything more i should get
7075 Adjustable Single Bell Crank Steering Set (k2121)
E4 Alum. 7075 Steering Block Set (k2110)
E4 Alum. 7075 Middle Shaft Mount (k2103)
E4 Alum.7075 Rear Bulkhead Upper Mount (k2144)
E4 Alum.7075 Front Bulkhead Upper Mount (k2143)
#3782
Tech Elite
iTrader: (13)
Why do you need extra low arms??
Do you use to long springs?
The RS arms(new type now) are low enough to do the job
About the K-factory parts, the E4 Alum. 7075 Middle Shaft Mount (k2103)
isn't all that needed.
It is nice and bling bling and perhaps gets you car up to weight without adding some lead to it but it is also expensive.
Give me a hoaler about the bulkheads as you know i can get my hands on some red one for a lot less then the K-factory price
The 3 degrees alloy C-hubs might also be a option instead of the middle mount.
regards Roy
Do you use to long springs?
The RS arms(new type now) are low enough to do the job
About the K-factory parts, the E4 Alum. 7075 Middle Shaft Mount (k2103)
isn't all that needed.
It is nice and bling bling and perhaps gets you car up to weight without adding some lead to it but it is also expensive.
Give me a hoaler about the bulkheads as you know i can get my hands on some red one for a lot less then the K-factory price
The 3 degrees alloy C-hubs might also be a option instead of the middle mount.
regards Roy
if you guys have extra lower arms front and back that your willing to sell and any other parts that i wi;ll need as back up let em know ill buy them off you guys
here is the list of k factory part im going to buy let me know if there is anything more i should get
7075 Adjustable Single Bell Crank Steering Set (k2121)
E4 Alum. 7075 Steering Block Set (k2110)
E4 Alum. 7075 Middle Shaft Mount (k2103)
E4 Alum.7075 Rear Bulkhead Upper Mount (k2144)
E4 Alum.7075 Front Bulkhead Upper Mount (k2143)
here is the list of k factory part im going to buy let me know if there is anything more i should get
7075 Adjustable Single Bell Crank Steering Set (k2121)
E4 Alum. 7075 Steering Block Set (k2110)
E4 Alum. 7075 Middle Shaft Mount (k2103)
E4 Alum.7075 Rear Bulkhead Upper Mount (k2144)
E4 Alum.7075 Front Bulkhead Upper Mount (k2143)
#3783
Tech Master
iTrader: (18)
Why do you need extra low arms??
Do you use to long springs?
The RS arms(new type now) are low enough to do the job
About the K-factory parts, the E4 Alum. 7075 Middle Shaft Mount (k2103)
isn't all that needed.
It is nice and bling bling and perhaps gets you car up to weight without adding some lead to it but it is also expensive.
Give me a hoaler about the bulkheads as you know i can get my hands on some red one for a lot less then the K-factory price
The 3 degrees alloy C-hubs might also be a option instead of the middle mount.
regards Roy
Do you use to long springs?
The RS arms(new type now) are low enough to do the job
About the K-factory parts, the E4 Alum. 7075 Middle Shaft Mount (k2103)
isn't all that needed.
It is nice and bling bling and perhaps gets you car up to weight without adding some lead to it but it is also expensive.
Give me a hoaler about the bulkheads as you know i can get my hands on some red one for a lot less then the K-factory price
The 3 degrees alloy C-hubs might also be a option instead of the middle mount.
regards Roy
the car is a fs with rs parts on it but when i got the car the right front lower arm was broke so i need one before i run it plus i want spare parts in case i brake them again lol
and for the red bulkheads i have nothing on the car that is red lol
i cant wait to run the car i so miss having a team magic e4
broken arm
almots done need to add my rx and get my new body and put on my new wheels
#3785
Tech Adept
iTrader: (5)
Hey that is a good looking car With the fs chassis I prefered the plastic bulkhead, a little more flex and what not. Sorry again about that arm man
Also I had flipped the steering crank around to get rid of bump steer. The guys at my track who where running the car more regularly than I was had real good results with that. Have fun with her and treat her right, she will be missed.
Also I had flipped the steering crank around to get rid of bump steer. The guys at my track who where running the car more regularly than I was had real good results with that. Have fun with her and treat her right, she will be missed.
#3786
Tech Master
iTrader: (18)
Hey that is a good looking car With the fs chassis I prefered the plastic bulkhead, a little more flex and what not. Sorry again about that arm man
Also I had flipped the steering crank around to get rid of bump steer. The guys at my track who where running the car more regularly than I was had real good results with that. Have fun with her and treat her right, she will be missed.
Also I had flipped the steering crank around to get rid of bump steer. The guys at my track who where running the car more regularly than I was had real good results with that. Have fun with her and treat her right, she will be missed.
the steering is set thatway becaue i hadto left the top deck up so my pack will fit so the steering links hit the deck so i changed it
ill change it after i test it if i have too
#3787
Super Moderator
iTrader: (62)
i got my pack to fit it was a pain im the a$$ but its in cant run it yet as one of the arms are cracked so i need to get some
if you guys have extra lower arms front and back that your willing to sell and any other parts that i wi;ll need as back up let em know ill buy them off you guys
here is the list of k factory part im going to buy let me know if there is anything more i should get
7075 Adjustable Single Bell Crank Steering Set (k2121)
E4 Alum. 7075 Steering Block Set (k2110)
E4 Alum. 7075 Middle Shaft Mount (k2103)
E4 Alum.7075 Rear Bulkhead Upper Mount (k2144)
E4 Alum.7075 Front Bulkhead Upper Mount (k2143)
if you guys have extra lower arms front and back that your willing to sell and any other parts that i wi;ll need as back up let em know ill buy them off you guys
here is the list of k factory part im going to buy let me know if there is anything more i should get
7075 Adjustable Single Bell Crank Steering Set (k2121)
E4 Alum. 7075 Steering Block Set (k2110)
E4 Alum. 7075 Middle Shaft Mount (k2103)
E4 Alum.7075 Rear Bulkhead Upper Mount (k2144)
E4 Alum.7075 Front Bulkhead Upper Mount (k2143)
There is a pic below... PM me for details if you are interested
#3791
Anybody have any news on the updated car ?? I keep looking at the TA06 but I still believe the E4 is a better design. I know in VTA and GT it's perfect. The tweaks in the upgraded version should make it a solid performer. Somebody give those folks at TM a kick in the ass so they don't drop the ball on this chassis.
#3792
Tech Champion
iTrader: (44)
Really the closest thing to the E4 is the old FSR car.
#3793
Don't get me wrong...I'm no Tamiya hater. In fact, it's the only NEW car I'd consider buying BUt....little things caught my attention like
1. No consideration for batteries that use banana plugs.
2. Wire routing looks even tougher than the E4. Anybody notice the pics of Satoshi's car where the battery wire is contacting the lower belt ??
3. Even the Tamiya junkies are questioning the layout of the IFS. It just seems wrong. The angle of the shock lever is odd.
4. Compared to the E4, the chassis extensions for the servo and esc seem quite wide. I guess thats why they had to angle them upwards.
Bottom line....the E4 is a really good chassis. Compared to many it's a breeze to work on and the layout just makes sense with little compromise. Little stuff already has fixes like that bulkhead at the left rear that makes motor movement a bit tight.
It seems to me that the changes to the newest version will make the car even better.
I think I'll stick with it. C'mon TM....give us your support.
1. No consideration for batteries that use banana plugs.
2. Wire routing looks even tougher than the E4. Anybody notice the pics of Satoshi's car where the battery wire is contacting the lower belt ??
3. Even the Tamiya junkies are questioning the layout of the IFS. It just seems wrong. The angle of the shock lever is odd.
4. Compared to the E4, the chassis extensions for the servo and esc seem quite wide. I guess thats why they had to angle them upwards.
Bottom line....the E4 is a really good chassis. Compared to many it's a breeze to work on and the layout just makes sense with little compromise. Little stuff already has fixes like that bulkhead at the left rear that makes motor movement a bit tight.
It seems to me that the changes to the newest version will make the car even better.
I think I'll stick with it. C'mon TM....give us your support.
#3794
Tech Champion
iTrader: (44)
What really is needed is better parts support. Really the parts prices for TM is a bit outrageous. I can get Serpent parts for 25% less. Why should TM parts be so expensive. Its not like they're XRay. If their parts were as durable as XRay, I wouldn't mind the cost by they're not.
#3795
Tech Elite
iTrader: (13)
YR4Dude???
Ever tried them->http://www.rcmanufactory.com/
Velly cheap
regards Roy
Ever tried them->http://www.rcmanufactory.com/
Velly cheap
regards Roy
What really is needed is better parts support. Really the parts prices for TM is a bit outrageous. I can get Serpent parts for 25% less. Why should TM parts be so expensive. Its not like they're XRay. If their parts were as durable as XRay, I wouldn't mind the cost by they're not.