3LikesCastle Creations Mamba/MM/MMM FACTORY Q&A thread!
08-27-2007, 10:45 PM
#797
Tech Regular
Originally Posted by wyd
Can always run offroad at Bumps and Bruises during the winter and keep running your brushless setup. You could run a 6900 or 7700 since traction is so freaking off the charts you can practicing doing wheelies all the time.
Other than the Max being a little large it works great and at least in offroad cars they fit easily. In touring I creative wiring and they fit in most cars. Works well in my MI3.
Other than the Max being a little large it works great and at least in offroad cars they fit easily. In touring I creative wiring and they fit in most cars. Works well in my MI3.
atleast it fits i got moungt it on an angle in the my ta05
08-29-2007, 05:24 PM
#798
Tech Adept
Look at this picture on Repair Invoice from CC,
and CRASH said.
Kidding?
I have a stutter problem. How can I do???
and CRASH said.
Originally Posted by CRASH
Yes, Joe works for Castle. New version of tech and he has not updated his signature.
If he told you to cut off the connectors and direct solder then no it should not void your warranty.
As for the shaft breaking yes that should be under warranty as well.
Call Joe direct at 913-390-6939 Ext 119
Later,
If he told you to cut off the connectors and direct solder then no it should not void your warranty.
As for the shaft breaking yes that should be under warranty as well.
Call Joe direct at 913-390-6939 Ext 119
Later,
Originally Posted by CRASH
I solder all of my motors directly to the ESC. I run touring car so this makes it easy. For offroad just solder the wires together and heat shrink. A little bit more trouble but in the long run you will be much happier.
Later,
Later,
I have a stutter problem. How can I do???
08-29-2007, 08:47 PM
#800
Originally Posted by C_Suzuki
do you run high power brushed mode or standard?
08-30-2007, 04:42 AM
#802
Tech Adept
Therefore, I can't do these???
I found all from this thread.
I found all from this thread.
08-30-2007, 05:05 AM
#803
It is my understanding that removing the plugs, shortening the wires and directly soldering the wires together does not void the warranty.
But removal of the wires from the esc circuit board itself and re-soldering of wires to it does void the warranty.
Please stay tuned for a official response from Joe Ford.
Later,
But removal of the wires from the esc circuit board itself and re-soldering of wires to it does void the warranty.
Please stay tuned for a official response from Joe Ford.
Later,
08-30-2007, 07:37 AM
#804
You CAN remove the gold connectors and solder the wires directly together WITHIN warranty. ANY soldering done on the controller itself VOIDS THE WARRANTY.
Joe Ford
Product Specialist
Castle Creations
Joe Ford
Product Specialist
Castle Creations
08-30-2007, 08:08 AM
#805
What Joe Said
Joe has posted our warranty policy.
08-30-2007, 08:53 AM
#806
Tech Legend
iTrader: (51)
Join Date: Sep 2001
Location: Castle Mamba Max Pro. Feel its power!!!!!!!!!!
Posts: 21,220
Trader Rating: 51 (100%+)
Originally Posted by rcracingkid
I just started to run the MM for brushed racing recently, and can honestly say that it has been off to a good start...
08-30-2007, 08:58 AM
#807
trying to contact joe check your pm
08-30-2007, 09:41 AM
#808
when its time to get those wires changed, do u have to send it in for new wire? eventually i'll need to, when who knows. but its an interestin question. hope no1 would get cute and leave the last 1cm of wire onto the board, then do all their other work via new wire soldered there.
just curious because...
...the receiver line is 'tired' (from being run under the battery channel and out on these 2wd buggies). i'd like to replace it, i'm adept at doin so (childs play compared to converting futaba G speedos to futaba Js that i did as a young man), but if it voids me out....eck thats a spot.
thx
R
just curious because...
...the receiver line is 'tired' (from being run under the battery channel and out on these 2wd buggies). i'd like to replace it, i'm adept at doin so (childs play compared to converting futaba G speedos to futaba Js that i did as a young man), but if it voids me out....eck thats a spot.
thx
R
08-30-2007, 11:08 AM
#809
Tech Legend
iTrader: (51)
Join Date: Sep 2001
Location: Castle Mamba Max Pro. Feel its power!!!!!!!!!!
Posts: 21,220
Trader Rating: 51 (100%+)
Originally Posted by ultegrasti
when its time to get those wires changed, do u have to send it in for new wire? eventually i'll need to, when who knows. but its an interestin question. hope no1 would get cute and leave the last 1cm of wire onto the board, then do all their other work via new wire soldered there.
just curious because...
...the receiver line is 'tired' (from being run under the battery channel and out on these 2wd buggies). i'd like to replace it, i'm adept at doin so (childs play compared to converting futaba G speedos to futaba Js that i did as a young man), but if it voids me out....eck thats a spot.
thx
R
just curious because...
...the receiver line is 'tired' (from being run under the battery channel and out on these 2wd buggies). i'd like to replace it, i'm adept at doin so (childs play compared to converting futaba G speedos to futaba Js that i did as a young man), but if it voids me out....eck thats a spot.
thx
R
08-30-2007, 11:12 AM
#810
hey b, its not that i worry over doin it. its the worry of doin it for normal maintenance and voidin a warranty b/c i like my stuff to be proper.
R
R
