FS futaba 9550 low profile servo

Old 10-06-2009, 07:18 PM
  #1  
Tech Lord
Thread Starter
iTrader: (32)
 
SuperEk4's Avatar
 
Join Date: May 2006
Location: Singapore
Posts: 10,333
Trader Rating: 32 (100%+)
Default FS futaba 9550 low profile servo

Hi, I have a mint condition futaba 9550 high speed low profile servo. Going for

TRADED

Interested call or txt me 9456 4029 Alan.

Low baller? Careful I high ball u

Specs

This is the S9550 Low Profile Digital Servo w/Two Ball Bearings for
Airplane and Car Use and Comes with "J" Connector Pre-Installed.
This servo will work fine with either 4.8V or 6V receiver packs.

FEATURES: Digitally Enhanced Microprocessor Cut About 1/2 of the Response
Time From Transmitter Input To Servo Reaction.
Low Profile allows for the servo to fit into wings and lay down
down in car chassis for less obstruction.
Coreless Motor
Metal Gears
Dual Ball-Bearings
High Torque
Case is Made of Black Plastic
Dust and Water Resistant (Not Waterproof)
High current/Low resistance servo leads.
Ideal for F3A aileron application and 1/10 scale electric touring car

INCLUDES: One S9550 Digital Low Profile Servo w/small Round Horn
Four Rectangular Grommets
One Three Arm Horn
One Wheel Horn

SPECS: Speed: .14 Sec/60 Deg @ 4.8V or .11 sec/60 deg @ 6V
Torque: 67 oz/in @ 4.8V - 83 oz/in @ 6V
(4.8 kg/cm @ 4.8V - 6.0 kg/cm @ 6V)
Weight: 1.6 oz (45g)
Length: 1.6" (41mm)
Width: 0.8" (20mm)
Height: 1.0" (25mm)

COMMENTS: S9550 Digital Servo Precautions,
-It is best to avoid long leads and Y-harnesses especially with
standard grade wires. If problems are encountered, consider using
heavy duty wire such as Futaba's Heavy Duty Series or Hobbico's
Pro Series, minimizing lead lengths, and/or removing Y-harnesses.
Current Drain: Futaba S9550 Servo is Specially Designed for High-
Torque and High-Speed, Therefore Very High Current Drain Is
Normal At Startup. For Ultimate Performance When Using This Servo
Please Review The Following Points.
(1) When Using Systems With the Battery Fail Safe Function it Has
a Higher Cut-Off Voltage Setting Which Will Cause Shorter
Operation Time.
(2) When Installing the Servo Please Check Pushrod Linkage To Make
Sure There Is No Binding in Order To Prevent Excessive Power
Consumption and Decrease the Life of the Motor and Battery.
Attached Thumbnails FS futaba 9550 low profile servo-servo.jpg  

Last edited by SuperEk4; 10-13-2009 at 07:21 PM.
SuperEk4 is offline  
Old 10-07-2009, 04:56 PM
  #2  
Tech Lord
Thread Starter
iTrader: (32)
 
SuperEk4's Avatar
 
Join Date: May 2006
Location: Singapore
Posts: 10,333
Trader Rating: 32 (100%+)
Default

Bump
SuperEk4 is offline  
Old 10-08-2009, 08:14 AM
  #3  
Super Moderator
iTrader: (76)
 
Funkymojo's Avatar
 
Join Date: Nov 2004
Location: Singapore ̡͌ ̴̡ı̴̴̡ ̡̡͡|̲̲̲͡͡͡ ̲▫̲͡ ̲̲̲͡͡π̲̲͡͡ ̲̲͡▫̲̲͡V
Posts: 3,452
Trader Rating: 76 (100%+)
Default

You called? Anyway bro, i had to delete those posts that were not related to your thread because there were reports made against this thread of yours. What to do, some people have a sense of humour and some do not...
Funkymojo is offline  
Old 10-09-2009, 05:22 AM
  #4  
Tech Lord
Thread Starter
iTrader: (32)
 
SuperEk4's Avatar
 
Join Date: May 2006
Location: Singapore
Posts: 10,333
Trader Rating: 32 (100%+)
Default

Bump
SuperEk4 is offline  
Old 10-09-2009, 07:36 PM
  #5  
Tech Addict
iTrader: (9)
 
Join Date: Apr 2005
Posts: 660
Trader Rating: 9 (100%+)
Default

bump for you, screw the losers.............
hoppie is offline  
Old 10-11-2009, 06:39 PM
  #6  
Tech Lord
Thread Starter
iTrader: (32)
 
SuperEk4's Avatar
 
Join Date: May 2006
Location: Singapore
Posts: 10,333
Trader Rating: 32 (100%+)
Default

prIce reduced $90

specs of 9550

SPECS: Speed: .11 sec/60 deg @ 6V
Torque: 6.0 kg/cm @ 6V)

specs of 9551

Futaba(#S 9551)-S 9551, Slim-Sized, 0.11-Sec/60, 8.8-Output Torque(KGS), Digital

You do not need 8kg for 1:10 off or on road.

Unless it's a 1/8 gp or 1/8 Ep car.

Last edited by SuperEk4; 10-11-2009 at 06:53 PM.
SuperEk4 is offline  
Old 10-13-2009, 01:29 AM
  #7  
Tech Lord
Thread Starter
iTrader: (32)
 
SuperEk4's Avatar
 
Join Date: May 2006
Location: Singapore
Posts: 10,333
Trader Rating: 32 (100%+)
Default

Traded

Last edited by SuperEk4; 10-13-2009 at 07:23 PM.
SuperEk4 is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Thread Tools
Search this Thread
Rate This Thread
Rate This Thread:
You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.