Go Back  R/C Tech Forums > General Forums > Electric On-Road
TT01 problems... help >

TT01 problems... help

Community
Wiki Posts
Search

TT01 problems... help

Thread Tools
 
Search this Thread
 
Old 11-18-2012, 05:58 AM
  #1  
Tech Adept
Thread Starter
iTrader: (4)
 
Join Date: Nov 2012
Posts: 142
Trader Rating: 4 (100%+)
Default TT01 problems... help

Hi all, I am running a TT01 as a drift car and sometimes when i turn right it turns left. To explain the complete problem.... if i turn left it turns left (normal), when i turn right it creaches forward and turns left and sometimes shifts.

It mainly happens after being driven for 10 minutes... is it shorting because things are gettign too hot? If i let it sit for 20 minutes and drive it the problem goes away... So, i think it has to do with gettign to hot. BUT, is it possible that it happens when the batteries are dying?

My setup

Tamiya TT01
losi esc
titan 12t motor
traxxas 27mhz
has drift tires


THANKS
Breitling is offline  
Old 11-19-2012, 05:51 PM
  #2  
Tech Adept
Thread Starter
iTrader: (4)
 
Join Date: Nov 2012
Posts: 142
Trader Rating: 4 (100%+)
Default

bump
Breitling is offline  
Old 11-19-2012, 06:55 PM
  #3  
Tech Master
iTrader: (19)
 
Joe Kimble's Avatar
 
Join Date: Feb 2012
Location: Miami, FL
Posts: 1,442
Trader Rating: 19 (100%+)
Default

Hi there, we ran the tt01 for the 24 hour race in Jackson NJ. That car is incredibly sturdy!

Anyway, I am no expert and your problem could come from different things but here are some suggestions.

It could be your steering servo that is tired. When a servo gets too old and has been used a lot, it can start acting funny.
It could also be your servo working too much and overheating. If that's the case it should come from your EPA that is not adjusted properly. I mean your EPA (or dual rate) throw might be set further than the actual steering possibility of your car. So when you're steering the servo tries to go way further than possible.
When not moving try to steer all the way and see if the servo is forcing further than the point when the wheels block. Then reduce your EPA or dual rate until the servo stops making noise.

If that doesn't work, try replacing your steering servo maybe? Also check all your wiring to make sure nothing is susceptible to short circuit?

All in all I guess it's always good to start with the obvious, which in your case seems to be the steering servo.

Hope this helps.

Last edited by Joe Kimble; 11-19-2012 at 09:17 PM.
Joe Kimble is offline  
Old 11-20-2012, 12:19 AM
  #4  
Tech Adept
 
Join Date: Aug 2010
Location: Somerset, UK
Posts: 106
Default

I suspect it's just your battery is flat. After 20 mins of rest it recovers some voltage and behaves. What Mah is the battery, what motor are running?
markrobinson is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.