HPI Cup Racer 1M
#2821
Tech Rookie
You need:
Important: You need part #13, plastic washer (4 of them) from both parts trees 85282 (there are 2 on each tree). These hold the clear o-ring in place before you clip in the C clip supplied with the new shock bodies.
- 2 sets #87070 Al shock bodies
- 1 set #87071 adjuster nuts
Important: You need part #13, plastic washer (4 of them) from both parts trees 85282 (there are 2 on each tree). These hold the clear o-ring in place before you clip in the C clip supplied with the new shock bodies.
#2822
Tech Champion
iTrader: (94)
Cup Racer roller for sale
Guys I am saying good bye to my Cup Racer, going to try out rear wheel drive M cars. Here's your chance to pick up a very clean, race ready Cup Racer
http://www.rctech.net/forum/r-c-item...er-roller.html
http://www.rctech.net/forum/r-c-item...er-roller.html
#2823
Tech Elite
Guys I am saying good bye to my Cup Racer, going to try out rear wheel drive M cars. Here's your chance to pick up a very clean, race ready Cup Racer
http://www.rctech.net/forum/r-c-item...er-roller.html
http://www.rctech.net/forum/r-c-item...er-roller.html
Sorry to see you go. Good luck with the M04/M06. Hope you run on high traction surfaces
#2824
Tech Elite
#2826
Hpi cup
I wish to buy a hpi cup car, shipped to Sweden. I have paypal.
thanks
M
thanks
M
#2827
Ygpm. Selling my new exotek club racer.
#2828
can i use Gear Differential Set back as well?
#2829
Absolutely, however I'm not sure if you can order it as a set or need to part it out individually. I ran my gear diff in the rear with good results. The car was really good with the diff loose in the rear and in order to do that with the ball diff back there it just got crunchy feeling over time. Probably miss adjusted on my part the first time though
#2830
Thank you for that answer. it can be ordered here.
http://www.amainhobbies.com/product_...fferential-Set
http://www.amainhobbies.com/product_...fferential-Set
#2831
Tech Champion
iTrader: (94)
Complete set of Cup Racer Aluminium shocks
Guys,
I sold my cup racer.. I do however have a set of 4 dampers left, they're built, but never used.
http://www.rctech.net/forum/r-c-item...l#post10358359
I sold my cup racer.. I do however have a set of 4 dampers left, they're built, but never used.
http://www.rctech.net/forum/r-c-item...l#post10358359
#2832
Tech Initiate
Hey CR lovers here is a question and i need yor help!! Is castle creations sidewinder sv2/4600kv motor combo right for CR??
#2833
lots of power. you'll have to crank it down, depending on your tracks and traction.
#2834
selling off my last CR
Its almost completely built.. you need minor stuff if you want every hopup that you need
http://www.rctech.net/forum/r-c-item...or-4slipo.html
Its almost completely built.. you need minor stuff if you want every hopup that you need
http://www.rctech.net/forum/r-c-item...or-4slipo.html
#2835
Tech Rookie
iTrader: (1)
Hay everyone ....this is my Cup Racer I bought off of Kmas a few weeks ago. Took me some time to finish the build (do to lack of funds) but all I can say is AWESOME!!! Im using it as a Drifter & I can honestly say...Its a lot better than I expected
Im still dialing in the set up but over all for a 50/50 Drifter, its working good.
-LRP SPX Zero ESc
-Trinity 17.5 BL motor
-Savox SC-1251MG Low Profile
-Spektrum SR300 on a DX3R (non pro)
Im still dialing in the set up but over all for a 50/50 Drifter, its working good.
-LRP SPX Zero ESc
-Trinity 17.5 BL motor
-Savox SC-1251MG Low Profile
-Spektrum SR300 on a DX3R (non pro)