The Speed Passion Thread
#468
Adam do you know any details are the new v3 any faster than the current v2 ones out currently now if so that would be awesome
#469
R/C Tech Elite Member
iTrader: (37)
Yes they will
I had mine on my SP motor checker last night and the V3 13.5 had 5000 more RPM then the V2 13.5 with zero timing advance on the motor, it was about 7200 more with the timing fully advanced.
Being it was on the motor checker I had the DRRS maxed out on level 9, and the timing on the ESC maxed out as well (26.25 degrees) I was running the 205G software on the SP GT 2.0 LPF
Being it was on the motor checker I had the DRRS maxed out on level 9, and the timing on the ESC maxed out as well (26.25 degrees) I was running the 205G software on the SP GT 2.0 LPF
#470
Awesome thanks adam
#471
although rpm is up there is probably a trade off in torque.
What size rotor does the new motor use 12.3 or 12.5 ?
What size rotor does the new motor use 12.3 or 12.5 ?
#473
Tech Elite
iTrader: (9)
I've been using a S/P GT L/P on the oval at my local club races.
Two races ago, I started having an issue that almost felt like a cogging...
on throttle it doesn't allow the motor to spin up ... it's like jerky, and lacks RPM's until it gets spinning
(This is w/ a 21.5 motor)
It's like a huge lag.
I thought maybe it was just a solder connection, so I resoldered, and unplugged and replugged the sensor harness.
(Just in case) I even changed Motor and Battery.
I have not changed over to the NEW Super Capacitor yet...
[b]Q[/q]
Is there anything else I may want/need to look at?
I have not re-setup the ESC yet, I may do that before the next race...
(The LAG kind of reminded me of the feel of a LIPO CUT OFF with a run down NiMh battery) We're using 2s Lipo.
Two races ago, I started having an issue that almost felt like a cogging...
on throttle it doesn't allow the motor to spin up ... it's like jerky, and lacks RPM's until it gets spinning
(This is w/ a 21.5 motor)
It's like a huge lag.
I thought maybe it was just a solder connection, so I resoldered, and unplugged and replugged the sensor harness.
(Just in case) I even changed Motor and Battery.
I have not changed over to the NEW Super Capacitor yet...
[b]Q[/q]
Is there anything else I may want/need to look at?
I have not re-setup the ESC yet, I may do that before the next race...
(The LAG kind of reminded me of the feel of a LIPO CUT OFF with a run down NiMh battery) We're using 2s Lipo.
#475
Tech Regular
iTrader: (20)
Setting up my SP GT 2.0 Low profile
Just a couple quick question, consider me a new to brushless..
I am running a cyclone with novak ss13.5, rubbers and a 4900 trakpower lipo.
Correct me if I am wrong using the little box I have set my lipo cut off to selection 5, 3.2 per cell. The lipo says not to drop it bellow 6v so 3.2 per cell is 6.4 lipo cut off?
Any other advice on setting this up would be appreciated; tweeking the other setting.
I do have a speedpassion 13.5 on the way. Should that be set up different to the Novak?
I have read back an understand this unit does not do brushed. I was planning on setting up another spare chassis to run black can 540. If I get the older 1.1 version of this speedo can I run brushed? or wiser to look at another model?
I am running a cyclone with novak ss13.5, rubbers and a 4900 trakpower lipo.
Correct me if I am wrong using the little box I have set my lipo cut off to selection 5, 3.2 per cell. The lipo says not to drop it bellow 6v so 3.2 per cell is 6.4 lipo cut off?
Any other advice on setting this up would be appreciated; tweeking the other setting.
I do have a speedpassion 13.5 on the way. Should that be set up different to the Novak?
I have read back an understand this unit does not do brushed. I was planning on setting up another spare chassis to run black can 540. If I get the older 1.1 version of this speedo can I run brushed? or wiser to look at another model?
#476
Tech Master
iTrader: (2)
OH -- for the brushed motor, consider getting a good used brushed only ESC... they are dirt cheap now, with everyone changing to brushless, and they are usually a bit smaller and lighter than brushless ESC's...
#478
Tech Fanatic
iTrader: (10)
adam, i know you can see updates and such from speedpassion regarding only 2 new software settings, but what about the previous software paramaters?
you updated my esc for my buggy, but im taking it to my Tamiya ta05ifsr and noticed it doesnt have that extreme low end punch i used to have. im sure it has to do with the software. how can i see the software list and what changes were made?
you updated my esc for my buggy, but im taking it to my Tamiya ta05ifsr and noticed it doesnt have that extreme low end punch i used to have. im sure it has to do with the software. how can i see the software list and what changes were made?
#479
Tech Fanatic
lost my usb forthe lcd program card
where can i get another usb cord for my programmer thxs reggie i lost it
#480
I just got my 2.0 pro carbon. Its great !!! I TQed and killed the motor in the A main lolol . Just wondering if anyone knows if this model has the latest soft ware?? and can you update it by pluging it in to your computer? Thanks