Team Associated TC5
#3136
spool pully
51,
Have you guys played with a smaller front pully for running a spool to gain back entry steering or do you guys adjust your setup to get it back?
Just wondering...
E
Have you guys played with a smaller front pully for running a spool to gain back entry steering or do you guys adjust your setup to get it back?
Just wondering...
E
#3137
Hey Guys,
any ideas when knuckles and other spare parts will be in stock???
any ideas when knuckles and other spare parts will be in stock???
#3139
Thanks, but they also are out of knuckles.
#3141
Tech Regular
iTrader: (1)
ran the car yesterday (prep'd asphalt)... I'm very impressed, the car out of the box responded very well (once I put on the right tires). I averaged 17-19sec lap times (I'm not that fast of a driver) Then I started to tweak the car, little changes; different camber link locations etc. I wound up returning back to stock, and changin the shocks to #2 pistons, 40WT & red springs all around. That change alone gained me an avg 15-16 sec lap times, my fastest overall was 14.8s
I'm happy with the chassis!!! more consistent than my TC3s, TC4 & FTTC4 (which has never been raced)
I'm happy with the chassis!!! more consistent than my TC3s, TC4 & FTTC4 (which has never been raced)
#3142
Tech Apprentice
iTrader: (3)
First post in this thread.
Just built up the 5 and am getting ready to club race it this weekend.
We run on a smaller mid size outdoor track on sprayed tarmac. Im in the air as to where to start on pinion size. Im rining a Novak V4.5, Stock Pinion and takeoff rubber tires.
Im guessing that a 20T would be a good starting point. Any thoughts on this?
Other then that, the Hightec 5625 fit right in and the kit went together without issue. Needed to drill the antena screw holes out and go back and install the servo saver that the instruction manual forgot to mention.
Im starting with the stock setup on the chassis. 40wt all around ans still flip floping on springs to use. For the springs Im leaning twords a setup sheet from the reedy race spec 19. I Forget who the driver was.
Great thread, learned a lot from it.
-Ed
Just built up the 5 and am getting ready to club race it this weekend.
We run on a smaller mid size outdoor track on sprayed tarmac. Im in the air as to where to start on pinion size. Im rining a Novak V4.5, Stock Pinion and takeoff rubber tires.
Im guessing that a 20T would be a good starting point. Any thoughts on this?
Other then that, the Hightec 5625 fit right in and the kit went together without issue. Needed to drill the antena screw holes out and go back and install the servo saver that the instruction manual forgot to mention.
Im starting with the stock setup on the chassis. 40wt all around ans still flip floping on springs to use. For the springs Im leaning twords a setup sheet from the reedy race spec 19. I Forget who the driver was.
Great thread, learned a lot from it.
-Ed
#3143
ran at SIR all day yesterday...
the car is grrrrrrrrrrrrrreat!!!!!
the car is grrrrrrrrrrrrrreat!!!!!
#3145
Tech Adept
iTrader: (11)
I broke one of my 4 degree caster blocks at the last race and it doesn't seem anyone is stocking this item yet. I ended up ordering the 2 degree caster blocks but was wondering how my suspension will change by going with 2 degrees less caster.
Btw, I was bashing the TC5 over the weekend and someone had a radar gun and clocked the TC5 at 32mph. This is with a BL 13.5ss on a 4.1 FDR. I was really amazed that it clocked so high.
Btw, I was bashing the TC5 over the weekend and someone had a radar gun and clocked the TC5 at 32mph. This is with a BL 13.5ss on a 4.1 FDR. I was really amazed that it clocked so high.
#3146
Tech Adept
Hi all, does anybody know how many teeth are on the belts? Just wondering if any other makers will fit?
#3147
Hey Brent, it was nice meeting you and Rick at the Off-Road Nationals this last weekend.
I'm currently running the Stellflue setup on my ride with the standard deck & o-ring mod.... is there another setup you guys have tried for a really low to med grip prepared ashplat surface?
I'm currently running the Stellflue setup on my ride with the standard deck & o-ring mod.... is there another setup you guys have tried for a really low to med grip prepared ashplat surface?
#3148
Cold one of you guys post the O ring mod in detail as I wold like to try cant seem to find it anywhere.
Cheers
Cheers
#3149
Hey Brent, it was nice meeting you and Rick at the Off-Road Nationals this last weekend.
I'm currently running the Stellflue setup on my ride with the standard deck & o-ring mod.... is there another setup you guys have tried for a really low to med grip prepared ashplat surface?
I'm currently running the Stellflue setup on my ride with the standard deck & o-ring mod.... is there another setup you guys have tried for a really low to med grip prepared ashplat surface?
the Tamiya track is Medium grip...so the teams setups from the Reedy should be very good....
#3150
killer Reedy Race wrightup is now on rc10.com!!!
check it out.....
check it out.....