JConcepts Thread
#7532
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
PW when are the dirt webs gonna be available for SC?
Same question. Need to get a set or 2 for SCT and ST before JConcepts indoor nationals. Am I going to make it?
#7535
#7537
#7539
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I just put this kit on my SC10.2 Everything fit pretty well. No real problems with the install. I will try it out tomorrow at the track and report back on how well it does.
I do have to say I had to replace the (4) set screws in the aluminum ends. My metric hex wrench would not fit, nor would my standard. First time I tried ti tighten the screw, it stripped. Had to slot it to get it out. Are they some special size?
Buzz.
http://www.jconcepts.net/store/index...roducts_id=696
I do have to say I had to replace the (4) set screws in the aluminum ends. My metric hex wrench would not fit, nor would my standard. First time I tried ti tighten the screw, it stripped. Had to slot it to get it out. Are they some special size?
Buzz.
http://www.jconcepts.net/store/index...roducts_id=696
Last edited by blvdbuzzard; 05-06-2014 at 04:28 PM. Reason: Forgot link
#7540
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I just put this kit on my SC10.2 Everything fit pretty well. No real problems with the install. I will try it out tomorrow at the track and report back on how well it does.
I do have to say I had to replace the (4) set screws in the aluminum ends. My metric hex wrench would not fit, nor would my standard. First time I tried ti tighten the screw, it stripped. Had to slot it to get it out. Are they some special size?
Buzz.
http://www.jconcepts.net/store/index...roducts_id=696
I do have to say I had to replace the (4) set screws in the aluminum ends. My metric hex wrench would not fit, nor would my standard. First time I tried ti tighten the screw, it stripped. Had to slot it to get it out. Are they some special size?
Buzz.
http://www.jconcepts.net/store/index...roducts_id=696
#7541
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I was using my new Dynamite set and my drawer full of the little "L" wrenches. I tried the new Dubro set too. Just seemed like it was small for the metric, large for the 050?
I have enough wheel collars and set screws it was not a problem. Could have been a bad lot of the set screws.
Buzz.
I have enough wheel collars and set screws it was not a problem. Could have been a bad lot of the set screws.
Buzz.
#7542
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
I was using my new Dynamite set and my drawer full of the little "L" wrenches. I tried the new Dubro set too. Just seemed like it was small for the metric, large for the 050?
I have enough wheel collars and set screws it was not a problem. Could have been a bad lot of the set screws.
Buzz.
I have enough wheel collars and set screws it was not a problem. Could have been a bad lot of the set screws.
Buzz.
#7543
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
parts is parts.
Is there a way to order parts for the sway bar kit? Brother lost one side of his rear sway bar linkage. It looks like the set screw came loose and the ball link came off the sway bar and then the link went flying. So, can we order the parts from JConcepts?
Buzz.
Is there a way to order parts for the sway bar kit? Brother lost one side of his rear sway bar linkage. It looks like the set screw came loose and the ball link came off the sway bar and then the link went flying. So, can we order the parts from JConcepts?
Buzz.
#7544
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
parts is parts.
Is there a way to order parts for the sway bar kit? Brother lost one side of his rear sway bar linkage. It looks like the set screw came loose and the ball link came off the sway bar and then the link went flying. So, can we order the parts from JConcepts?
Buzz.
Is there a way to order parts for the sway bar kit? Brother lost one side of his rear sway bar linkage. It looks like the set screw came loose and the ball link came off the sway bar and then the link went flying. So, can we order the parts from JConcepts?
Buzz.
#7545
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
parts is parts.
Is there a way to order parts for the sway bar kit? Brother lost one side of his rear sway bar linkage. It looks like the set screw came loose and the ball link came off the sway bar and then the link went flying. So, can we order the parts from JConcepts?
Buzz.
Is there a way to order parts for the sway bar kit? Brother lost one side of his rear sway bar linkage. It looks like the set screw came loose and the ball link came off the sway bar and then the link went flying. So, can we order the parts from JConcepts?
Buzz.